Question about Maytag Washing Machines

1 Answer

Maytag bravos mct ecoconserve leaking water

If i pour water into the tub when it's turned off it leaks out the bottom

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Hi Kim, what you need to do is lean the washer back to see where the leak is coming from. It could be a split hose or a damaged tub. You could also have a bad tub seal. If it's not easily visible,you may need to call a local repair company. Hope that helps.

Posted on Jun 04, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Washer_tech

Geoff Siegel

  • 164 Answers

SOURCE: MAYTAG PERFORMA is leaking

the bearing and seal are worn and leaking. if the machine is a good oe and the repair cost is reasonable, i would have it repaired. contact your local repairshop and determione the cost vs replacement of machine

Posted on Nov 17, 2007

Bill Dozier

  • 262 Answers

SOURCE: leaking water from bottom of tub

this is bad it needs a center seal/bearing kit this is qite common in the Amana / Maytag line.they are kinda hard to install you may need a service tech to do this for you the kit runs around 80.00 dollars and has instructions. if you need more help you can email me at familyappliancerepair@yahoo.com

Posted on Dec 07, 2007

22yooper

James Helmer

  • 828 Answers

SOURCE: maytag side by side freezer leaking water and icing in bottom

Defrost drain system is plugged and not draining out the back and into the drain collector. There is normally an air trap in this drain line under the back and behind a fiber removable panel. Check this trap and make sure it is clear of any blockage. You will then have to defrost the freezer and clear out the ice. Don't forget to replace the back fiber panel.

Posted on May 17, 2008

Anonymous

SOURCE: WATER LEAKING FROM FRONT BOTTOM

Check your door boot, ours is doing the same thing. Found out there's a huge hole in the door boot seal.

Posted on May 29, 2008

Anonymous

  • 1 Answer

SOURCE: maytag neptune mah5500bww leaking water

Here is the solution I found that worked for me, there is a small drain hole at the bottom of the boot that is connected to a drain hose. Remove the hose and clean out to make sure that it has not become plagged. replace hose and reattach boot. Mine stoped leaking imediately.

Posted on Aug 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Elite model #11027087603. How do I remove tubseal nut on bottom of washer that holds motor rotor on shaft?


that should have an inset, hex-headed screw/bolt. You will have to hold the rotor with one hand and use your other hand to loosen that screw. they use thread lock on that screw, so it will be difficult. but, that's only half the battle. You will have to remove the tub cover, agitator (7/16 agitator nut size), and the spin basket to access the tub seal. the seal has to go on from the inside of the tub assembly. Make sure you don't use anything against the outer lip of where the seal seats inside the tub, or you will have to replace the outer tub because it will still leak. Push the seal all the way down. then before you put everything back together, pour a small amount of water in the tub and see if you see any leaks. anything major will show then, but if there is a small leak, you will not know it till you try to wash with it. You shouldn't have to remove the stator screw or do anything from the bottom side of this unit. You should be able to replace that seal from the top side. good luck.

Nov 28, 2015 | Kenmore Washing Machines

1 Answer

Water pours from bottom of tub as soon as water goes in.


Common cause is leak in drain hose as hose outlet must be above water level and if damaged water will run out straight away ( syphon ) but tip it up ( carefully ) and check
Please - Please be carefull as water and electric are not friends

Aug 31, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from...


you just need to clean the pump area in the bottom of your unit :)
try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :)

Aug 12, 2009 | KitchenAid 24 in. KUDS25SH Built-in...

1 Answer

Leaking below washer


Sounds like you have a leak from the tub. Either the seal in the bottom of the tub or a hole in the tub.
When you run it again try feeling around the bottom center of the tub for water or try to see if water is leaking any where out of tub. Clear water would be from the supply line , soapy water would be from tub or a hose coming out of tub.

Jun 09, 2009 | Washing Machines

1 Answer

WHEN I TURN WASHER ON WATER STARTS POURING OUT OF THE BOTTOM OF THE MACHINE AND ONTO THE FLOOR. WATER IS COMING FROM THE BOTTOM LEFT SIDE.


The drum seal is bad. The seal allows the center to come up through the tub and the tub to rotate around it, It usually has a rubber membrane that flexes so the tub can rock around. The rubber tears and the water runs right out. If you can, disassemble the washer and change the seal, otherwise the washer is toast. Sorry! You can verify this by pouring water in from a bucket. If this water doesn't run through then it is the hose from the fill valve to the water outlet under the lid.

Jun 08, 2009 | Washing Machines

1 Answer

About 1 minute into the cycle water starts running out from underneath of the washer. Checked all the hoses that are connected to the back and none are leaking


this is either the front seal that goes from the outer tub to the front of the washer or a hole in the outer tub itself or one of the hoses underneath the seal and the hoses are easiest to check you can take a cup of water and slowly pour it into the front seal. take care not to overfill it to where it spills into the tub and see if you are getting water on your floor from that. the hoses tip the washer up onto its back and look at them from the bottom for any cracking etc. the tub itself can only rust out on some of the neptune models or on others is plastic and can get punctured. just have to look for damage with a light and a mirror.

May 19, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Water coming out of the bottom


It could be a hole in one of the hoses or a possible leaking pump. tip the unit back so you can see underneath. Not all the way though. I usually prop it against the wall. you should see the pump it has 2 hoses going to it one from the tub to pump and one from the pump to the drain. Check those, check the hoses, check the tub for a hole. More than likly it's a bad pump

Jan 05, 2009 | Roper RAS8445KQ Top Load Washer

2 Answers

Water Pouring out of the soap dispenser


ckd the line from dispenser into tub start inside tub first look for clothing caught at inlet point pull dispenser drawer out and ck from dispenser end may try pouring water in from that end also if happen to use dry detergent an undisolved lump may be caught somwhere in between

Nov 08, 2008 | Washing Machines

1 Answer

GE Top load washer.


Hello rschneeweis
Welcome,

Sounds like a seal or drain hose is leaking or the clamp on a hose has vibrated loose.

Water leaking out the bottom of the machine when washing machine begins agitation cycle. If the machine is turned off the water stops leaking even with the tub full of water.

Let me know if you found it and how you do.

Huuum
Please remember to leave a rating

Oct 04, 2008 | GE WBSR3140D Top Load Washer

1 Answer

Water leak


Remove the lower panel under the washer door and inspect the interior. The panel is removed by loosening and removing the screws under the bottom front edge. With the screws removed the panel will drop down, then off. Inspect the following areas:

- Check all hoses for leaks, cracks, holes and loose connections. Check the seal where the drain hose from the bottom of the wash tub connects to the intake of the drain pump. Make sure the drain hose from the pump to the standpipe is connected snug to the pump and is not leaking.
- Check the drain pump to ensure it is not leaking. The clean out reservoir cap (if not fitted properly) can leak around the seal.
- Check the door bellow (gray rubber boot) to ensure it is not leaking. HINT: A tale-tell sign of bellow leakage is wetness showing up on the front washer counterweight. This is a concrete block mounted to the front of the wash tub. It is not supposed to be wet.
- Check the pressure switch air hose to ensure it is connected to the air dome on the side of the wash tub. This is a small rubber hose that runs from the pressure switch in the top left rear of the washer (viewed from the back, with the washer top panel removed) to the bottom right hand side of the wash tub. However, if this hose were to come off the air dome fitting, the wash tub would continously try to fill and water would begin to pour from the bottom of the wash tub. If this does not sound like your symptoms, disregard this step.
- Check the seam where the wash tub shells meet. There is a rubber tub gasket that seals the two tub halves together. If the seal is bad, water will begin to collect and drip along this seam.
- Check the tub for cracks. This is NOT common, but it can happen.

The following link explains the step-by-step process of checking and cleaning the drain pump:

http://www.fixya.com/support/r385845-checking_drain_pump_in_whirlpool_duet

I mention this link, because it gives you some guidance on how to access the pump and how avoid the possible mess involved with water pouring out of the pump.

If you discover the door bellow as the the cause for your leak, please refer to this link:

http://www.fixya.com/support/r385211-replacing_door_bellow_whirlpool_duet

I hope this leads you in the right direction and helps you resolve your problem. Please post back if you have any further questions.

Aug 06, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...