Question about Kenmore Kitchen Ranges

1 Answer

Have a kenmore c970-595084 and says F1 stove top still works oven does not. None of the electronic board works. Stove top is not part of the board as they have the historic knobs

Posted by on

  • David Del Polito
    David Del Polito Oct 03, 2019

    Kenmore model numbers are as a example
    110.2907864 so to check it out you need the model number and it’s usually down below the oven door. Open the draw and look at the leg for a tag

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Hey D, f1 can be one of three problems. A stuck key pad,test by pressing all the buttons to see if they all make noise, if one doesn't then that's the stuck one. A bad oven temperature sensor, if it's gone bad it will not send the proper temp reading to the control board. Or it could be a bad control board itself. If nothing is working/changing mode it's most likely the stuck keypad. If you're not comfortable working with electrical components I suggest calling your local repair company to check it out. Hope that helps.

Posted on Oct 02, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 126 Answers

SOURCE: Oven stopped working while cooking a meal

it sounds like it burnt one of your main wires in the back of range. by turning a knob on you are getting a feed back. turn the power off remove back panel take a visual check of your wiring.

Posted on Dec 14, 2007

Anonymous

SOURCE: have a magic chef oven, f1 display after self cleaning

Your sugestion does not work.I press CLEAR/OFF and power off several times, the F1 error and beeping is continue every 2 minutes. Any other suggestion?

Posted on Jan 02, 2008

Anonymous

  • 1 Answer

SOURCE: Stove reads "F1" on the display and beeps

Go to www.applianceaid.com/images/ge-built-in-oven-faultcodes

Posted on Sep 20, 2008

Anonymous

  • 8 Answers

SOURCE: stove works, oven does not

in repairing Kenmores there is a relay well 2 small black an square in the head unit of stove one for stove the other is for oven anyway they go out alot a setback to the kenmore digital controls take upper panel off where controls are look at the green board an you can see them some green some red or blue to tell if one is bad be careful an turn the stove on u will hear the relay click then try oven if you do not hear a click its bad do not i repeat do not touch it while its on

Posted on Oct 11, 2008

Anonymous

  • 750 Answers

SOURCE: electronic touch pad not working on my oven

Hello beachlady80,
Welcome

You said, It was working fine last night but when you woke up this morning the display has 3 vertical lines and none of the electronic touch pads work. The burners on top of the stove still work.

What is the model number and how old is the range ?

Try turning the breaker off for 10 minutes and then on again after this allotted time.
This may reset the system.
Let me know how it works.


Waiting for your answer.
Huuum

Please remember to leave a rating.
Hopefully it will be a solved!
Let me know

Posted on Oct 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My oven when turned on goes to F1 and the heat is like broil...only the top burner comes on????


Hello,Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

May 28, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

2 Answers

Moved into this house. Has no manual on Kenmore glass top stove, on how to use self cleaning oven. Looking for manual or directions on how to use it. Only have model # 790.96011400 and serial # VF50635079


Hi,
Before you go working too hard to get you oven to go into the self clean mode....check out this tip...


http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!! " - amymrocks

Apr 13, 2010 | Ovens

1 Answer

Whatt is an F1 fault on the kenmore stove


HI, This code is indicating that the main control board has failed. This will require you to have the damaged circuit board replaced, asap. This type of damage that has occur, is not repairable. The board must be replaced.

F-1 - Board Failure.

Dec 11, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

Oven doesn't work, stove does


If it's a Whirlpool or Kenmore oven (or one of several other brands that are made by Whirlpool) then this error code means:

F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC)


The system believes that the control board has failed and needs to be replaced.


This page has a list of diagnostic codes by brand and model number. You should check there to look up your particular brand to confirm what I just said.


Aug 04, 2009 | Ovens

1 Answer

66993 pizza oven microwave oven combo pizza oven not heating error code f1 microwave part works


Hello, please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

Jul 20, 2009 | Kenmore 63662 / 63664 / 63669 Microwave...

1 Answer

Kenmore smooth top stove has a code f1 on display oven. what is wrong?


Your electronic control board is bad. (clock).
It must be replaced.

May 12, 2009 | Whirlpool RBS245PDS Electric Single Oven

1 Answer

Stove top elements f1 error code


Hi. you can try to reset the electronic oven control by unplugging the unit for 3 mins. if the problem still exist, you will have to replace the clock/control(electronic range control).

please rate and god bless:)

Apr 02, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

My kenmore oven is beeping and will not stop. the display shows F-1.


Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Dec 16, 2008 | Ovens

4 Answers

My kenmore electronic stove is having a beep with code F1 on the


Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Dec 15, 2008 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

Kenmore 8114p643 showing f1.


F1 is either a bad electronic control board or a bad touch pad.

You find the solution on :kenmore oven with "F1" error

I quote:
"You have either a bad ERC (clock) or a bad touch pad.

    1. Disconnect power to stove
    2. Gain access to the back of the clock (electronic range control or ERC).
    3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire apx. 1 1/2" to 2" wide.
    4. Make sure everything is clear and will not short out when power is turned back on.
    5. Turn power back on to stove.
    6. Watch for the F1 and listen for the beep.
    7. If you get the F1 and beep, replace the ERC.
    8. If after apx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
      NOTE: Some models incorporate the touch pad and the clock as one part.
If you can't find a new ERC you can send yours to stove clock repair and get it repaired!"

Dec 14, 2008 | Kenmore 91112 / 91114 / 91117 Electric...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6063 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Paul Carew

Level 3 Expert

3484 Answers

Are you a Kenmore Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...