Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I am needing the 2 handwheels and the lever for the fence. Where can I find them? This is for 6 Delta jointer..

1 Answer

Tom Chichester

Tools & Hard... Master 62,329 Answers
Posted on Dec 21, 2020

Tom Chichester

Tools & Hard... Master

Joined: Jul 14, 2012

Answers

62329

Questions

Helped

672128

Points

975369

Delta or a Delta supplier might have

5 Related Answers

Anonymous

2176 Answers
Posted on Apr 05, 2009

SOURCE: Manual for Delta Shopmaster 6" Jointer

Go to Dewaltservicenet.com and in the middle of the page towards the bottom type in your model number. It will take you to another page and click on the first JT160 and when it changes screens click on the instruction manual, I had to click on it a couple times to open it but I did look at and it is about 48 pages long. Let me know if you have any problems and I will check further

efs_perpends

1997 Answers
Posted on Apr 06, 2009

SOURCE: Need manual for Jointer

Go to this link and you'll find a complete parts diagram, list, and pdf manuals for your jointer.
Dewalt service net

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take a moment to kindly rate this post....thanks!

Anonymous

2176 Answers
Posted on Sep 24, 2009

SOURCE: need a replacement motor for 1972 craftsman jointer

went to Sears site and no luck most parts are discontinued. So maybe try Grainger with the information from the data plate on the motor for a replacement or check in yellow pages for a local dealer of electric motors. I don't really think that there should be anything special as long as the output shaft and mounting are the same. Good luck sorry I don't have better info for you.

Anonymous

2176 Answers
Posted on Oct 23, 2009

SOURCE: need manual for delta jointer model number 37-196

go to Dewaltservicenet.com and type in your model number and on the next page you will that another model supersedes yours, click on the instruction manual for this one it is 25 pages long, the manual for your tool is not available online.

Anonymous

2176 Answers
Posted on Feb 17, 2010

SOURCE: Owner's manual for Delta Shopmaster Model# JT160

go to Dewaltservicenet.com and type in your model number in the bottom of the page the manual is 56 pages long. If I have helped you would you please rate this response accordingly.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

In feed table is not level from front of table to fence

Fill feed table with water and measure water level at all corners and adjust until all corners have the same water depth. Then then drain and fill with feed. The fence should be near the feed table.

Read full answer

Aug 12, 2013 • Delta X5 Dj20 8" Precision Jointer

1helpful

1answer

Delta jointer, where do i find the wrench to loosen the nuts for the blade

go to Dewaltservicenet.com and with your model number you can download a schematic for this tool and also order the parts online. I tried finding them but there are too many jointers listed in the Delta category.

Read full answer

Apr 16, 2011 • Delta Jointer Blades 6 Inch Fits , Jet...

0helpful

1answer

Eg2175need manual for craftsman 6inch jointer model number 113 20 680

Go to partsdirect.com and type in your model number. From there, you can order whatever you need for your jointer.

Read full answer

Feb 06, 2011 • Delta Jointer Blades 6 Inch Fits , Jet...

0helpful

1answer

I have Delta 37-200 jointer and am wondering how to set the knives and level the in feed table and and the out feed table?

Go to eReplacementParts.com : Power Tool Parts and Tool Repair.

If you need more help come back.Post / thumbs / testimonial are welcome!

Read full answer

Nov 15, 2010 • Delta Machinery Delta 37-658 Jointer...

0helpful

1answer

We need a manual for a delta dj 15 jointer around 15 years old? would appreciate any help

I just tried to upload the manual to the site but it wouldn't let me due to the size so I'll just give you the link to go and get it. http://www.dewaltservicenet.com/servicenet_home.aspx When you go to the website there is a box "Need a Manual" just type DJ15 and it will bring it up for you.

Read full answer

Nov 08, 2010 • Delta Machinery Delta 37-275X X SERIES 6"...

1helpful

1answer

How do you make the outfeed and infeed tables paralell? The infeed table closest to the blade is a little lower than the other end? Any suggestions?

Instruction manual is here.

Exploded diagram is here.

I'm pretty sure you're saying your planer tables are not coplanar.

http://thewoodwhisperer.com/jointer-setup/ is worth watching. Despite his comments about a level, a decent level works fine for making sure your tables are flat and coplanar on smaller units like this.

On more expensive planers there are gibs that can be adjusted to fix this issue. Your part list doesn't list any gibs, so it looks like you will have to loosen the screws holding the infeed or outfeed table in place and shim it. You can use a metal feeler gauge to figure out how much need to shim it.

Also, if you're still in warranty, Delta may be able to replace your unit. If you're going down this route, I'd recommend you take a level and your unit into a service center so you can show them the problem.

Be aware that the replacement "could" be worse than the original. Be sure to check it. I recently waited 6 weeks for a replacement fence for my jointer (mine developed a twist) and the new one had a 3/8" bow in that was ridiculous.

Unfortunately the Shopmaster line wasn't Delta's greatest and there have been a lot of problems with them. It might be worth keeping an eye on craigslist in your area, as decent prices can be had on jointers fairly regularly.

Please vote if this answer was useful.

Read full answer

Jun 10, 2010 • Delta JT160 Shopmaster 10 Amp 6 Inch...

1helpful

1answer

I need to find blades to fit a delta 6" X5 jointer, model 37-866x

go to Dewaltservicenet.com and under the service locator on the right hand side type in your information. The blade set number that I came up with is 37-658 and they show that as qty 3 in one package.

Read full answer

Mar 19, 2010 • Delta Jointer Blades 6 Inch Fits , Jet...

1helpful

1answer

Need manual for Jointer

Read full answer

Apr 04, 2009 • Delta JT160 Shopmaster 10 Amp 6 Inch...

0helpful

1answer

Fence gets a slight bow in it when tightened

look at the far end of the fence for a nut that you can loosen slightly when in the unclamped position. It sounds as if you are clamping it so tight that you are bowing the fence

Read full answer

Mar 21, 2009 • Delta Saws

0helpful

1answer

Technical

a jointer includes infeed and outfeed tables. A set of rotating blades is positioned between these two blades. A fence is set on one side of the jointer to serve as a guide. The infeed table and outfeed table are adjusted so that they are parallel, but the infeed table is slightly lower thereby exposing a small amount of the cutting blades. The woodworker then presses the lumber against the infeed table and pushes it onto the outfeed table; the rapidly spinning blades remove a small amount of material. If the wood is particularly warped, several passes on the jointer may be required.

Read full answer

Aug 27, 2008 • Delta 37-108 Push Blocks for Jointers

Not finding what you are looking for?

View Most Popular

Tools & Hardware - Others

In feed table is not level from front of table to fence

Delta X5 Dj20 8" Precision Jointer

234 views

Ask a Question

Usually answered in minutes!

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual

Related Topics:

Trustworthy Expert Solutions

I am needing the 2 handwheels and the lever for the fence. Where can I find them? This is for 6 Delta jointer..

1 Answer

Tom Chichester

5 Related Answers

Anonymous

efs_perpends

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

In feed table is not level from front of table to fence

Delta jointer, where do i find the wrench to loosen the nuts for the blade

Eg2175need manual for craftsman 6inch jointer model number 113 20 680

I have Delta 37-200 jointer and am wondering how to set the knives and level the in feed table and and the out feed table?

We need a manual for a delta dj 15 jointer around 15 years old? would appreciate any help

How do you make the outfeed and infeed tables paralell? The infeed table closest to the blade is a little lower than the other end? Any suggestions?

I need to find blades to fit a delta 6" X5 jointer, model 37-866x

Need manual for Jointer

Fence gets a slight bow in it when tightened

Technical

Not finding what you are looking for?

Tools & Hardware - Others

In feed table is not level from front of table to fence

Ask a Question

Top Tools & Hardware - Others Experts

Brad Brown

john h

ADMIN Andrew

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Manuals & User Guides

Gasprosuperpropro2propiezoinstruction....

100-1.2.pdf. user-manual-Taco Red...

Rockwell-rk2515k2.pdf....

Related Topics:

Trustworthy Expert Solutions

I am needing the 2 handwheels and the lever for the fence. Where can I find them? This is for 6 Delta jointer..

1 Answer

Tom Chichester

5 Related Answers

Anonymous

efs_perpends

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

In feed table is not level from front of table to fence

Delta jointer, where do i find the wrench to loosen the nuts for the blade

Eg2175need manual for craftsman 6inch jointer model number 113 20 680

I have Delta 37-200 jointer and am wondering how to set the knives and level the in feed table and and the out feed table?

We need a manual for a delta dj 15 jointer around 15 years old? would appreciate any help

How do you make the outfeed and infeed tables paralell? The infeed table closest to the blade is a little lower than the other end? Any suggestions?

I need to find blades to fit a delta 6" X5 jointer, model 37-866x

Need manual for Jointer

Fence gets a slight bow in it when tightened

Technical

Not finding what you are looking for?

Tools & Hardware - Others

In feed table is not level from front of table to fence

Ask a Question

Popular Questions

Need staples for my Swingline Heavy Duty Tacker #800

I have purchased an fitbit one and it comes up with code 541 is ineligible for an account how can I make an account?

Why when I put my paslode battery on to charge

I have a very old Bostitch staple gun Model T5.

What does F03 mean

Top Tools & Hardware - Others Experts

Brad Brown

john h

ADMIN Andrew

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Manuals & User Guides

Gasprosuperpropro2propiezoinstruction....

100-1.2.pdf. user-manual-Taco Red...

Rockwell-rk2515k2.pdf....