Question about Kenmore Refrigerators
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
don't know this appliance but for guidence:
some appliances have the evaporator in a compartment at the top of the freezer and the drain comes out of the back and runs externally to the drip tray. there should be a grill in the compartment so just peer into it and see if there is ice build up.
wherabouts is the freezer ice forming?
Posted on Sep 05, 2008
SOURCE: remove panel
the freezer panel has 2 fan motors, one for the i/m area and the other for cooling. there is 1 screw in the center of the panel, remove it and then the panel will have to be wedged out. it may seem like it is tight but go ahead and pull on the panel and it will come out.
before you can do this, you will need to remove the drawer and rails so you can get into the panel easily.
p.s. you didnt say why you want to remove this panel???
by the way, these units have problems with the fan motors causing poor cooling in the refr section.
Posted on Dec 28, 2008
SOURCE: water leaking into refrigerator
yes you have to take off the ice maker then remove the scews, sometimes there is a air channel that has to be removed which are held in by plastic tabs
Posted on May 06, 2009
check the fan that transfers the cold air from the freezer to the fridge. thats where it comes from if you didn't know that. also check the the fan on the condenser at the bottom of the fridge. it should be blowing hot air off the condenser to facilitate the elimination of the heat from the condensing unit, just like your a/c does on the houe.
Posted on Jul 21, 2009
SOURCE: I have ice forming on floor of freezer. Kenmore Coldspot model 106.64244400, our research says we need to defrost and remove back panel to clear the drain, but we have no idea how to remove the panel
If the water is showing on the freezer side, more than likely you have a clogged drain. This occurs when the machine goes into defrost and the melted ice somehow is prevented from draining and therefor refreezing and blocking the drain for the next defrost cycle. The best way to resolve this is to unplug the machine for atleast 24-48 hours to let all ice melt. If thats not an option that you want to use the actual repair method would be to 1) unplug the machine 2) empty everything out of the freezer so you'll have room to work 3) take all the shelving and baskets out 4) locate the screws on the rear wall inside the freezer and remove them 5) take the back panel off exposing the evaporator coils ( the aluminum ) 6) directly below the coils is a trough of sorts and the drain is usually in the middle and runs out the bottom, remove the ice by carefully chipping it out or by using a hair dryer or hot water. 7) once all the ice is gone, the drain is visible and water can flow smnoothly down the drain dry the area and reassemble.
If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3
Posted on Jun 05, 2012
Tips for a great answer:
Jun 06, 2014 | Kenmore 73502 / 73504 / 73509 Bottom...
Sep 25, 2010 | Kenmore 62232 / 62234 / 62239 Bottom...
Jan 31, 2010 | Kenmore Refrigerators
Sep 06, 2009 | Kenmore 55612 / 55614 / 5561 / 655619 Side...
Jul 17, 2009 | Refrigerators
Dec 27, 2008 | Kenmore Elite 22.4 cu. ft. Bottom Freezer...
Sep 04, 2008 | Refrigerators
Jun 10, 2008 | Amana ABB1927DE Bottom Freezer...
124 people viewed this question
Usually answered in minutes!