Question about JVC Televison & Video

3 Answers

JVC TV LT-32G80BU can't navigate in menu + all channels messed up

After a vacation where the power was off, I come home and all the channels on my TV is messed up, they're all shuffled from 1 to 80 (got 30).
When I enter the Menu, I can't do anything, when I hit the down button it just goes down one channel. The EXT5-HDMI is not showing anymore either. It's only 3 years old, how do I reset it? or get it back to normal. I tried do another power off for 10min, but still the same.

Please help. thanks.
/Morten

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

TV seems to reset it's settings for some reason (it happened to me with similar TV - LT-32A80SU). I have found the way to solve this situation - service menu.

Press button "i" and "mute" on remote at the same time - service menu should appear. Now press 8 and there should be menu that allows to change few advanced features. Pressing down and up arrows allows to navigate, pressing right and left arrows changes values. You have to change "dual HDMI" to YES (this will enable second HDMI port) and change "remocon" to other option available (this will change how the remote behaves). Save settings by pressing OK button. Now you can leave service menu by pressing "i" button twice. You should now be able to use your TV like before.

Remember - these are instructions for my TV and they worked for me but playing with service menu can be dangerous so you're doing it at your own risk. Ask JVS support if you're not sure what to do.

Posted on May 12, 2011

  • Golffreak May 27, 2011

    I have exactly the same problem and this is the right solution. Thanx a lot.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It works!!! :)

Posted on Jan 19, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I have the exact same issue and with the same model!!! did you find a solution???

Posted on Dec 26, 2009

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have jvc tv model LT-24C660, I turn on tv massage come “no channels added yet. Please go to the installation menu to add channels.” How can I go to installation menu?


Do you have cable or satellite? Satellite uses only one station and all you have to do is select the station your satellite provider told you to use. If it is cable then go to your menu screen and look for "setup." That should get you going.

Nov 22, 2017 | JVC Televison & Video

1 Answer

XCAN'T FIND THE BUTTON TO RUN CHANNEL AUTO SCAN


First make sure that the Source is set to TV and a good antenna/coaxial cable is connected to the TV. Use the Input button on the TV (to the left of the power button) or the Input Select button on the remote. Use the up/down arrow keys to navigate through the source list and press Enter to select that choice. (On the TV, the Input button is the Enter button.) Next press the Setup/TV Menu on the remote (or Menu on the right arrow button or Enter. Then go down to Auto Ch Memory and press the right arrow or Enter. With the up/down arrows, navigate to Signal Type and set that to Air (for OTA channels) or Cable with the left/right arrows. Now navigate to Automatic Search and press the right arrow or Enter. Wait for the scan to be completed.

I hope this helps. The steps are shown in the manual for the LT-19D610 on page 18. The manual is available from JVC on the product page: http://support.jvc.com/consumer/product.jsp?modelId=MODL028825 . The direct link to the manual is http://resources.jvc.com/Resources/00/01/47/J55D0221B.pdf .

Cindy Wells

Dec 05, 2015 | JVC LT-19D610 19" 720p 1366 x 768 35000:1...

1 Answer

I have a JVC LT 26X575 that will not accept remote input for any function, but using the buttons on the TV allow the menu to be achieved and the sound to be raised or lowered. In TV mode it comes on on...


sounds like the remote batteries could be bad or the buttons on the remote need to be cleaned. some JVC TV remotes, I'm not familiar with this particular one though, can be cleaned using a clean pencil eraser. Be careful opening the remote because some parts can fall out or you can damage the connections to the LED emitter that sends the signal to the TV. Also the solder connections on that LED could be bad.

Jun 07, 2017 | JVC LT-32X575 32 in. HD-Ready LCD...

2 Answers

Dish Satellite recently installed in my home supporting several tvs. MY JVC TV model LT32E478, designated as TV1, does not recognize any channels during program scanning. As a result, the timer on/off...


Hi mfaille
I`m going to help you with your setup but first;
Which connection are you using from the sat receiver to the tv?
Coax / standard rg6 cable?
Did you try to manually add(in the menu/tuner setup/find channel/add) the channel you need ?

May 17, 2010 | JVC LT-37E478 TV

1 Answer

My tv won"t turn on.


1. Hold [menu] and [vol-] button on the side of the TV
2. while holding these, press the [power] button on the side of TV (NOT remote)
3. blue light comes ON and stays ON
4. wait 10 seconds then let go of [menu] and [vol-]
5. wait another 30 seconds and some type of picture should appear

I think this is right. I got it from the JVC call centers guys so sorry if I missed or messed up a step.

Apr 07, 2009 | JVC LT-42X579 42 in. LCD TV

4 Answers

JVC LT-32P679 Blinking Power Light, Automatic Shutoff


1. Hold [menu] and [vol-] button on the side of the TV
2. while holding these, press the [power] button on the side of TV (NOT remote)
3. blue light comes ON and stays ON
4. wait 10 seconds then let go of [menu] and [vol-]
5. wait another 30 seconds and some type of picture should appear

I think this is right. I got it from the JVC call centers guys so sorry if I missed or messed up a step.

Mar 17, 2009 | JVC LT-32P679 32 in. LCD TV

2 Answers

JVC LCD TV LT-42X688-powers on, blank screen. no picture,no sound


You most definately have bad capacitors in the power supply. try and get it repaired as soon as possible, not an expensive repair that iv'e seen.

Feb 04, 2009 | JVC LT-32P679 32 in. LCD TV

2 Answers

JVC LT 32E479 UNABLE TO SWITCH ANY CHANNELS


Please my jvc television couldnt change to stellite channel when i was offing it mistakenly pressss the +button i have been trying to change channels but i couldnt please is there any solution to that?please i need urgent help
12_9_2018_12_57_37_am.jpeg

Jan 14, 2009 | JVC LT-32E479 LCD TV

1 Answer

After power outage, TV screen is blank


It sounds funny but, unplug the set for 30 seconds to allow the TV to reset then see if the problem still is there.

Apr 10, 2007 | JVC LT-26WP84 26 in. LCD Television

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

570 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...