Nf code and donnot continue to next cycle - Frigidaire Affinity ATF7000E Front Load Washer

I believe you have a Samsung washer. NF means that the washer is not filling with water. Please check if the water supply faucets are opened.

Samsung Washing Machine Shows NF or 4E Error Code What Does This Fault...

If the unit was working fine before bearing repair, then I lean toward wiring issue. Do a visual inspection of the water valve and all the wires to it. One might have been put in wrong place. If wiring is correct, then maybe a bad water valve. The water valve has multiple solenoids and the one for rinse might be bad. I still think its a wiring issue. Good Luck!

The main PCB has failed and needs to be replaced. Here is a link to the part you need. http://www.appliancepartspros.com/samsung-assy-pcb-main-dc92-00658b-ap5579722.html Washing Machine Repairs Central Coast NSW

Check the filter screens. At the water hose connector there should be a screen just inside. Clean it with a stiff toothbrush.

Bonnie,

NF = No Fill the control board receives signaling for the washer during the water fill cycle. With most cycles the depth of water is around 3.5 inches in the wash basket. I know a Bulky Wash cycle selection will fill the wash tub to a high fill which is about 7.5 inches of water in the wash basket.

Is the washer filling the machine with any water? Do you hear water entering the machine? If you are doing a cold water fill and there is no or very little water in the wash basket with the NF error code. Try a Warm or Hot fill and see if the machine will fill and start the wash cycle.

Assuming you are doing cold water wash loads. You could have a water line block at the inlet screen or a failed cold water inlet valve which will not open. Try the above and let me know the results..........Rich

The machine needs to cut you a break;

“”i have a maytag neptune TL and there are several things wrong with it...1. I can't wash small loads it will stop at the spin cycle and flash dc””

This issue is a clutch issue see this post to DIY the repair.

“”it will wash fine on regular loads until it comes to spin cycle again and it will stop and flash nf””

This one is a little confusing the “nf” error is a No water fill error code. Check these two post for support regarding water inlet restriction or valve not opening properly.

nf post nf post 2

“”my fabric softener dispenser will not let the softener out neither will the bleach dispenser””

See this fabric softer post for support. The fabric softener dispenser may be clogged or the water dispenser valves feeding both dispensers may not be operating properly. The Service Manual on page 16 “Board Output Test” will give you support to turn on the Fabric Softener Valve and Bleach valve. See if you hear the valves operate in Service Mode”

My method may seem a little confusion for viewing water flow to the dispensers. This issue could be associated to the nf error you are receiving, restricted water flow (inlet screen clog) or cold water valve not working properly.

Post back for any questions or possible support I can offer. I’m an owner like you not a repair person but I’m very comfortable working on this machine. Rich

nf means u have a bad water valve u may also have a bad hose underneath the lid as well if u have water in your control

Tell me, do you notice the water filling and going against the "glass" door and going straight to the overfill trap bellow the door?

Let me know.

The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad. I hope this helps you.