Question about Bosch Nexxt 100 Series WFMC1001UC Front Load Washer

2 Answers

Why doesn't it wash?

Door locks, water starts coming in for about 2 secs and stops. Wash light comes on and that is it. It does nothing more.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 118 Answers

The first burst of water indicates an active circuit to the inlet valve momentarily. Then the action stops. Check that the door is locked closed.The door lock switch controls power to the machine The electronic looks for this and may decide to shut down if anything is not satisfied At startup a test is performed by the electronic controller. The pressure fill switch may be at fault but this is not that common If the drain pump is blocked and there is still somewhere in the tank from previously this should be checked. Remove the pump trap cover and drain the machine from there checking nothing is stopping this by looking inside from where the cover was removed. After this if no satisfaction you will need a professional person to assist. Good luck. PS the water valve its self could have a faulty diaphragm that stops the flow. There are a few possibilities that a technician could work through.

Posted on Jun 11, 2015

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Bosch Master
  • 5,420 Answers

No agitation?

first use a multi meter and check ur water pressure switch? that is what sends the machine the message to start wash cycle?
You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube.
If the machine starts to wash. the pressure switch is more than likely good
( If No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED) another test u can do is Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well.
Or take the original hose tube and plug one end and blow into it AT the other end, it should be hard and have pressure, if it is easy to blow and u dont feel any pressure and it feels like the air is going out ?
Sometimes they get busted open or a pin hole and release air causing the water switch diaphragm to not open.


Another test u can make with a multi meter is by testing the prongs individually.
# 15,16,17 (don't worry to much bout the numbers IF U GET THEM WRONG) place ur meter prongs on both out side prongs or connectors of the switch.
(where the wire plugs into) take note of weather it shows OHMS or infinity ( open or close circuit) ? Now place the meter on the left outside and the middle prong, take note agin what it shows. Now place meter prong on the right outside and the middle prong. Agin take note what reading u get. ( you should actually get a reading of infinity in 1 and a reading of continuity or ohms in the other 2? Now the tricky part. Agin place a small tube or hose into the switch and blow into it, using the meter do the same test agin on all prongs. But now keep the pressure on the switch when u blow into it, in other words use ur tongue on one end of tube to not allow air to escape. When u test it agin now one of the prongs that once read infinity should now show continuity or ohms, and 1 of the other prongs that read ohms should now read infinity or open.
.

If both check ok then next CHECK the motor coupler (a bad couplercan be checked by looking under the machine and taking note if there is a black residue on floor, look at coupler located between the motor and tranny, and see if it is broken up or missing any parts? Try to turn shaft by hand and notice if it does not engage tub? )
or belt if belt driven. Check for loose, broken or worn belt .

Then check the door switch with a multi meter for continuity OHMS when door closed and infinity when door is opened , and if there is a little movement on wash cycle in 1 direction only then check the cam dogs in agitator.

Also check THE CAM DOGS INSIDE THE AGITATOR, AS THEY WILL HINDER THE AGITATION PROCESS. However in G.E models the cam dogs are replaced with what is called an agitator coupler. (located at bottom of tub)
Remember to check the agitator spline as well. for worn broken teeth
By the way my advice is free cuz God is good!




Why doesn't it wash? - door-locks-water-starts-coming-in-about-nmtrxuhfc1nopxoeyhsrubgi-2-0.jpg







door-locks-water-starts-coming-in-about-nmtrxuhfc1nopxoeyhsrubgi-2-14.jpg
Why doesn't it wash? - door-locks-water-starts-coming-in-about-nmtrxuhfc1nopxoeyhsrubgi-2-20.jpgt-nmtrxuhfc1nopxoeyhsrubgi-2-20.jpg" alt="door-locks-water-starts-coming-in-about-nmtrxuhfc1nopxoeyhsrubgi-2-20.jpg" class="h_mi" />

Posted on Jun 08, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Load got off balance, I believe, and now it will not come on.


It sounds like bad electronics or bad sensor, did you try to adjust front door while turning machine on, like push them in. Do water runs in, if not it can be water switch.

Apr 04, 2016 | Washing Machines

1 Answer

Wash Cycle will not start; ADD GARMENT and DOOR LOCKED lights on.


IF you take the panel off the is below the door, there is a drain plug and you should take it out. YOU will get lots of WATER. Be ready. Clean this out and try again. The issue is most likely the water solenoid valve is bad or the board that controls it is bad. You can also find the tech sheet when you look for the drain. It has all the tests that you can run.

Feb 01, 2014 | Kenmore HE2 Washing Machines

1 Answer

Single mother of four wash machine not working only 2 yrs old.


Take off electricity wire, Open the filter from the front( maybee need to remove a rectangular cover.) turn the filter anti-clockwise. take out the hairneedle or coin. (the water will come out from the filter so make preparation with towels., see inside the filter if something is stucked around the small propellar. Turn the electricity back on. choose for example pumping program or centrifugeprogram. After that the machine should work.

Jun 01, 2013 | Whirlpool Washing Machines

1 Answer

Kenmore Ultrawash dishwasher Model 665 15810000. Originally "water heating" light was flashing and no water in dishwasher. Replaced water inlet valve. Turned power back on, normal wash light goes on...


lock light is locking the panel push this child lock button for 3 sec and see if it un locks . then try it again .. may have a pannel out. mm

Dec 06, 2009 | Washing Machines

1 Answer

Maytag Neptune Front Loader Washer


Sounds like the door lock unit isn't locking and may be bad. It is also a possiblity but not likely that there could be a problem with the computer board but start with the door lock unit first

Dec 29, 2008 | Maytag Neptune Washer

2 Answers

Hotpoint wf 250 aquaries


try changing your water valve this should sort problem

Jun 11, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Maytag neptune washer


Doesn't your unit have a lock light in addition to an on light? On mine when you start the machine a red light comes on, then after a minute or two the lock light above it comes on. Once the lock light lights, the machine shouldn't stop. If only the initial light comes on, the door isn't locking. As a result, as the drum moves the clothes and they push against the unlocked door, it turns the machine off. You might need to check/tighten the door latch. Also check the door wax motor/door lock assembly.

Dec 10, 2007 | Maytag Neptune MLG2000A Front Load Stacked...

1 Answer

Washer door pops open during wash cycle


Start the washer in a cycle. When the door locked light comes on, before unit gets to full of water, see if you can pull door open. If so, you probably have a broken latch. The wax motor is activating the switch, but latch is not actually closing. There was a door latch upgrade for some of these models.

Oct 06, 2007 | Maytag MAH6500 Neptune Front Loading...

2 Answers

Wash starts it fills with water then stops and wont wash


problem may just be that drum is not turning so you think program is stopped. try cancelling and select spin program and see if you get spin

Apr 01, 2007 | Hotpoint WMA44 Front Load Washer

Not finding what you are looking for?
Bosch Nexxt 100 Series WFMC1001UC Front Load Washer Logo

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...