I need an upgraded motor control board - Maytag Neptune MAH5500B Front Load Washer

If you live in North Hollywood, CA and need washer repair service call us at (626) 460-0903 or visit our website Washer Repair North Hollywood CA 747 248 4544 Samsung

please test the output voltage from control board motor, for voltage measure in terminal motor, if there are NOT voltage in output the control board is faulty.

2) Test if there are voltage terminal motor, if there are the motor need to be test. Loose the belt and try again. and if the motor RUn YOU need to LUBE the deck belt board.

God bless you

These are a closely guarded secret and not available outside of the factory.

What do you need it for?

Toner Suction Fan Motor (M11) Failure:

M11 connector is on the Mechanical Control Board (PWB-A),

Also check the Power Supply Unit (PU1)

Mechanical Control Board Cover

1. Remove the Upper Rear Cover.

2. Remove the Rear Cover.

3. Remove five screws [1] and the

Mechanical Control Board Cover [2].

4. Unplug the all connectors.

5. Remove five screws [3] and the

Mechanical Control Board [4].

NOTE

? When replacing the Mechanical

Control Board, be sure to replace

the EEPROM.

? When the Mechanical Control Board

has been replaced with a new one,

check the ROM version and

upgrade the firmware to the latest

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Try the heat limit switch it could be stuck open take it out and clean the back off it

if it is still tumbling in wash cycle,the motor and motor control board on the bottom are OK.The problem will be in the main control board in the top consol.board should then be replaced.If tub is not moving at all it could be the motor control board located on the bottom of the machine in front.When this board goes bad you can usually see signs of burning parts on the board.This part will be replaced with an upgrade kit consisting of a new board and new drive motorfor around 275.00 approx

Are you sure it's not actually working (tracking)-- can you hear the motor running?

I would contact Orion and make sure you have a manual for the hand-controller-- it may have a setting that turns tracking on or off.
http://www.telescope.com/control/main/

without knowing the exact error message, I can only speculate, but most rewind errors I have seen with the AJ-D230 are related to problems with capacitors on either the reel motor driver board or the system control board. the firewire upgrade (AJ-YAD230) is no longer available.

I've only seen one of these belts break in my 7 years of fixing Neptune's. I have replaced dozens of motor/ motor control board kits. Maytag upgraded the washer motors about 5 years ago, if yours is older it's probably got the older style motor. If that's the case you need to verify that the motor control board is getting power from the main control board, if it is, then you need to replace both the motor and motor control board (it comes as a kit). If it isn't you need to put 120 volts to the motor control board and see if the motor spins at 50 rpm (normal agitate speed), if it does, you just need the main control board, if it still doesn't run you need the main board and the motor/ motor control kit. If it has the newer motor, you would also need to test and replace the motor and/ or the motor control board separetly.

Could be just about anything. It's all designed to prevent it from spinning if there is a problem. If the motor is still turning, but never gets up to spin speed, check the out of balance circuit. There are two cabinet strike switches and an inertial unbalance switch. Or check the door latch assembly, it's possible for the door to lock enough to turn the 'door lock' light on, but not move far enough to actuate the 'spin enable' switch. Maytag has upgraded the motor/ motor control board for the older Neptunes. If the motor is not running at all, check that the main control board is sending power to the motor control board. If it is you need the motor/ motor control kit (just one part #) If the main board is not sending power to the motor control board, you need a main control board, but you still need to test the motor control board. Take a test cord and put 120 volts to the motor control board, the motor should start turning at 50 rpm (normal agitate speed) if it doesn't you would need the motor/ motor control kit as well.