Why cannot make any call but received from other

The fax machine may be in secure receiving mode. The following is from the User's Manual section on Faxing. downloadcenter samsung com

Receiving in secure receiving mode

You may need to prevent your received faxes from being accessed by unauthorized people. You can turn on secure receiving mode to restrict printing of received faxes when the machine is unattended. In secure receiving mode, all incoming faxes go into memory. When the mode is deactivated, any stored faxes are printed.

Activating secure receiving mode

1. Press (Fax) on the control panel.
   

2. Press Menu until Advanced Fax appear.
   

3. Press the left/right arrow until Secure Receive appear and press OK.
   

4. Press the left/right arrow until On appear and press OK.
   

5. Enter a four-digit password you want to use and press OK.
   

   You can activate secure receiving mode without setting a password, but cannot protect your faxes.
   

6. Re-enter the password to confirm it and press OK.
   

7. Press Stop/Clear to return to ready mode.
   

When a fax is received in secure receiving mode, your machine stores it in memory and shows Secure Receive to let you know that there is a fax received.
Printing received faxes

1. Access the Secure Receive menu by following steps 1 through 3 in "Activating secure receiving mode."
   

2. Press the left/right arrow until Print appear and press OK.
   

3. Enter the four-digit password and press OK.
   

   The machine prints all of the faxes stored in memory.
   

Deactivating secure receiving mode

1. Access the Secure Receive menu by following steps 1 through 3 in "Activating secure receiving mode."
   

2. Press the left/right arrow until Off appear and press OK.
   

3. Enter the four-digit password and press OK.
   

   The mode is deactivated and the machine prints all faxes stored in memory.
   

4. Press Stop/Clear to return to ready mode."
   

Wireless speakers connection

LED indicator of wireless receiver
LED Color Operation

Blue - The Wireless Receiver is receiving the signal of the wireless transmitter.

Red - The Wireless Receiver is in standby mode.

Off (No display) - The Wireless Receiver is turned off.


Initial setting an ID of wireless receiver

1. Connect the Wireless Receiver and the rear speaker (right, left) with the speaker cables.
2. Connect the power cord of the Wireless Receiver to the outlet.
3. Turn on the main unit and Wireless Receiver: The main unit and wireless receiver will be automatically connected. "MATE OK" appears in display window. Setting an ID of wireless receiver When the unit is manufactured, the ID is already set. If an interference occurs or you use a new wireless receiver, an ID should be set
again.

1. Turn on the main unit and turn off the wireless receiver.
2. Press and hold x (STOP) on the front of unit and MUTE on the remote control. "REMATE" appears in display window.
3. Turn on the Wireless Receiver. A new ID is set.

Turning On and Standby
On the AV receiver, press the [ON/STANDBY] button.
On the remote controller, press the [RECEIVER] button, followed by the
[ON/STANDBY] button.
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
To turn the AV receiver off, press the [ON/STANDBY] button, or press the remote
controller's [ON/STANDBY] button. The AV receiver will enter Standby mode.

If you have any trouble using the receiver, a simple reset could solve your problem.Note that resetting the AV receiver will delete your radio presets and custom settings.
To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [ON/STANDBY] button. "Clear" will appear on the display and the AV receiver will enter Standby mode.


Hope you are satisfied with my solution.Your valuable feedback would be appreciated.Thanks for choosing Fixya.

TinuAlbinAlex

http://www.retrevo.com/support/Denon-AVR-589-Receivers-manual/id/23110dj893/t/2/
This is a site where you can download a manual. I'm not familiar with Denen however, you should be able to go out of satellite receiver(HDMI) to your receiver input(tv/sat) then to your HDMI input on tv. Your receiver might show video and sound through another port of receivers options, ie; video 1, video 2, etc. Check all putput options for your picture and sound. Hope this helps.

http://www.quietpcusa.com/Moneual-MK700-Wireless-Keyboard---Black-Silver-P371C0.aspx

7-9. Receiver Part

D813, D814 = 1.5V? Resolder UCP200 or change PBA


Receiver does not work
SPK800 +,- PAD = 1.5V? Resolder UCP200 or change PBA


Is Receiver working? Replace the Receiver


Check the soldering of the
Receiver contacts


Modify the receiver FPCB soldering

why not you use a normal AV cable
instead of hdmi cable

depend on what you wants to do. if you wan to get sound from your tv on receiver connect out from tv to in on receiver if U have optical out from tv send this to optical input on your receiver and set up your receiver to impute to digital HDMI carrie sound and video...

(My Denon receiver set-up shows an HDMI cable going from the Video Out on the TV to the HDMI MONITOR OUT on the receiver)
OUT TO OUT don't make sense ...could be out to impute you may have HDMI going from receiver to TV and other HDMI imputs on receiver to use receiver as distribution unit say you have satellite HDMI, DVD HDMI, Computers HDMI IMPUTE all of this connected to your Receiver and the HDMI monitor out from your receiver connected to TV so now you may select any of this sources to wach In your TV and lessen trough receiver speakers