Can i use my microphone on my boss rc 50 looping machine?

Hi, This is all you want to go for Boss products and support. Best.

http://bosstonecentral.com/

if your using it from the battery ck that the wires are tight connected and the battery clips are tight (both ) if the electronics senses a very quick power interruption then yes it will reset the loop back

Perhaps your computer's sound card is unable to play back at the bit rate and kHz you are recording at on your (mobile?) recorder. I'm not familiar with the RC-50 but if you are recording at 24 bit for example and your computer's sound card is only able to play back at 16 bit it may not reprosuce any sound. Usually you will get an error saying so. Have you tried different playback software?

If your Roland BOSS RC-20XL Loop Station will not record or play, there are a few troubleshooting steps you can try:

1. Check the power source: Make sure that the Loop Station is properly powered and that the batteries or power supply are providing sufficient power. If using batteries, try replacing them with fresh ones.
2. Check the connections: Ensure that the input and output connections are properly connected and that there are no loose cables. Try using different cables to see if that resolves the issue.
3. Check the settings: Make sure that the Loop Station is set to the correct mode and that the input level is set appropriately. Refer to the user manual for guidance.
4. Reset the device: Try resetting the Loop Station to its factory settings. Refer to the user manual for instructions on how to do this.
5. Service: If none of the above steps work, the Loop Station may need to be serviced. Contact the manufacturer or a certified repair center for assistance.

Hopefully one of these steps will help you get your Roland BOSS RC-20XL Loop Station working again.

While you can probably get the functions sent by MIDI to transfer to the other unit, syncing PROBABLY isn't going to work very well because there is a lag to form the MIDI sync clock (serial data) and then receive it, decode it and do something with it.The transmit time is about 1/3000 of a second and receiving is at least that much time. On rhythm things I have found the ear can hear 1/1000 of a second easily. If one could set the machines to use an EXTERNAL sync clock and drive the SAME clock to both units, you might be able to sync them together time wise as they would see the sync at identical times.

CHeck the voltage out of the adapter. It should be around 9 to 11 volts. If it is not, it is possible that the OC3 has reversed polarity AND a protector that put a short on an incorrect supply. If so, it could have damaged the RC50 adapter. If the RC50 adapter is putting out correct voltage, then I suspect the inout connector on the RC50 may be damaged or not quite seated. Visually inspect the connector first.

USB port for data/audio backup, import/export of loops as WAV files http://www.bossus.com/gear/productdetails.php?ProductId=772

Ok, solved this problem by visiting roland U.S. site as the help offered in this country is useless. The instructions given by email would not have worked even after the update was installed. Luckily, there are instructions that come with the download. If you have same problem as me go to http://www.rolandus.com/products/productdetails.php?ProductId=772&tab=downloads&skip=true

and update the opperating system on the RC-50 to RC-50 System Update Version 1.01.

Then hold loop sync and phrase 2 button (think it was phrase 2) to change it to sound priority mode. Then it will play back correctly what you recorded on the first loop, rather than missing the first beat.

Am v.happy I have found this, as after much searching I can't find any other loopers out there that offer 3 seperate loop tracks and the ability to switch between them effectively. Plus, it's a very convenient size, better than a load of rackmounted stuff to haul around.

However.....

Another problem..

When hitting the reverse switch ( I assigned both external footswitch and the onboard Tempo pedal to reverse) the change is not instanteaneous. There is a second or so delay before it plays in reverse. Not a problem for most, I suppose, but I have a piece that switches rythmicaly between playing forward and reverse which means hitting a pedal in time and reverse/forwards changing immediately. I think they could do with another software update to solve this. Now I have to keep room in my enormous pedal board for the old rc-20, as that does the reverse as it should - when you hit the flippin switch!

From what I remember from my recent tinkering you press the guide select button. Then either use the patch/value know and parameter buttons, OR it may be the guide level knob to switch the volume down until it is off. I believe I then saved the patch to preserve the setting and keep that irritating guide at bay! It really should be more intuitive, ideally knod turned to zero = OFF. But no. Ah well, hope you get it sorted. I have a problem too, maybe you have same one? It may be the unit itself. Search - Beggining of loop missing on FIRST playback - if you get a chance. Let me know if yours does it too?