Question about Kenmore 43142 Front Load Washer

Open Question

After wash cycle complete water drains out then starts to fill for rinse cycle. water starts but never fill as if the the water continues to drain the the water runs forever

Posted by Anonymous on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: kenmore stack washer and dryer

gabehart....sounds like belt is slipping. Replace it. The water pump is on a separate smaller motor so is not affected by the agitator/spin motor.

Posted on Aug 11, 2008

Ad

Anonymous

SOURCE: Whirlpool Model LSV6234AWO

door switch bad?

Posted on Oct 18, 2008

Anonymous

  • 61 Answers

SOURCE: water runs into tub but does not fill?

be sure the drain hose is not lower than the wash tub this will caust the water to run out, 2nd be sure the drain hose is not pushed to far into the house stand pipe and the there is rome for air to go inbetween the drain hose and stand pipe eather of these will cause the machine to siphon mostly on rince cycle or on the 2nd and third loads you do. last your house drain could be starting to back up fill the washer with water and listen to it drain if you hear a gurggling sound in the house pipe you may need a plumber to cleanthis out for you.

Posted on Jan 20, 2009

jsrock516

Jeff Rockwell

  • 5911 Answers

SOURCE: Kenmore front load washer won't drain

Remove the bottom panel under the door to access the drain pump. Make sure the washer is unplugged before servicing the pump. The pump will be located under the wash tub in the front of the washer. There should be a small access cover that can be unscrewed to access the inside of the pump. If not, remove the inlet hose to access the pump impeller. HINT: Pull the drain hose from the standpipe and use a shop vac to pull a vacuum on the drain line. This will pull any remaining water out of the drain lines and wash tub. This will minimize the amount of water that spills out of the drain pump when you remove the access cover.

It does not take much to damage this small drain pumps. If you clean the pump thoroughly and it still exhibits drain problems, the manufacturer recommends replacing the pump.

If you require additional assistance, let me know before you rate the solution. I hope this helps you.

Posted on Feb 02, 2009

SOURCE: won't complete cycle, stops at rinse. and can't get hot water.

Are you on well water? turn off the cold water to the washer and clean the screen filter out. do not leave filter out.
the machine probably has a cold only final rinse so it won't work properly.

Posted on Apr 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher and Paykel 7.5 washing machine keeps powering off during rinse and spin cycles


The pump has a thermal safety cut out on it.
If the pump gets too hot it cut out.
Just put a new pump in and your all going again.

Aug 05, 2012 | Fisher and Paykel Washing Machines

1 Answer

My frigidaire front load washer will start a wash, complete the first cycle but then stop and flash all the lights and beep continously until I press "start" or "cancel". If I press "start" again it just...


Hello there:
If your cycle does not complete or The cycle doesn't advance
When the cycle should advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. than check the cold water supply line and the filter

Aug 15, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Spin/drain cycle won't start


If the timer gets to the rinse cycle and stops,
Check the lid switch for continuity. If no continuity replace the lid switch.
If the timer continues through rinse and spin without doing either, replace the timer.

May 21, 2009 | Kenmore Washing Machines

1 Answer

Washer will not advance in the rinse cycle,water just runs continuely.


check the drain hose it should be only 6 to 8 inch in your drain line if drain hose is all the way in the drain line correct it and you will be fine.

May 21, 2009 | Washing Machines

1 Answer

Water will not stay filled in tub on rinse cycle


It sounds like a siphon issue.
Check that the drain hose does a high loop before it goes into the drain pipe. (ie. drain hose loops above the water level inside the tub). Make sure the drain hose is not pushed too far down into the drain pipe. Also if the drain hose is sealed to the drain pipe this will create an airlock and a siphon will occur, allow air to enter between drain hose and drain pipe connection.
This should help you but if there is still a problem let me know and I'll try to assist you further.
Good luck!

Mar 21, 2009 | Maytag Washing Machines

1 Answer

Water runs into tub but does not fill?


be sure the drain hose is not lower than the wash tub this will caust the water to run out, 2nd be sure the drain hose is not pushed to far into the house stand pipe and the there is rome for air to go inbetween the drain hose and stand pipe eather of these will cause the machine to siphon mostly on rince cycle or on the 2nd and third loads you do. last your house drain could be starting to back up fill the washer with water and listen to it drain if you hear a gurggling sound in the house pipe you may need a plumber to cleanthis out for you.

Jan 19, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Whirlpool Washer - Imperial Series Quiet Wash 2


your washers drain hose is too far down the drain pipe which is causing a siphoning action pull the washers drain hose out pipe some you should be able to hear water dropping into the pipe the reason it only happens in the rinse cycle is because the water from wash is being drained and before the water vacuum is broken the rinse water comes in causing it to keep draining

Dec 30, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Incomplete wash cycle.


It sounds as if you have something acting as a flap causing the restriction. You should take the hose that leads from the tub to the pump off and see if there is anything just inside the tub. I have noticed that alot times you could have a coin that blocks the opening. You may have to remove the inner tub to remove anything in there

Dec 30, 2008 | Maytag SAV3655A Top Load Washer

Not finding what you are looking for?
Kenmore 43142 Front Load Washer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

James Hensley
James Hensley

Level 2 Expert

161 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...