What is error code 2402

Question edited for clarity and toss in some CAPS.
Question moved to category.

Error Codes > Konica-Minolta > bizhub 500 > Code C-2402

Printcopy.info https://printcopy.info > code=C-2402
Code: C-2402; Description: Erase lamp (EL) connector slip-off abnormality. - When EL turns ON before starting an initial charging, EL abnormality has been ...

Missing: press ‎C6000 ‎Pro.

Bizhub PRESS C6000 error codes

Copytechnet https://www.copytechnet.com > ... > Konica Minolta
Aug 7, 2013 - 1. Check the connection between the rear side connector of the fusing unit and the main body side connector, and repair it if any abnormality.

Step 1
Step lightly on the scale until it displays "--", "0000" and turns off if you receive the error "ERR0," which means the scale is not initialized. Initialization must occur after each battery installation.
Step 2
Set the scale on a flat, even surface, not on surfaces such as carpet if you receive an error "ERR1."
Step 3
Step off the scale and wait for it to reset before stepping on it again if you receive an "ERR2," which often means the unit was jarred or overloaded. Also, if you weigh more than the maximum weight capacity you will receive this error.
Step 4
Remove your shoes and socks and wet your feet slightly with a damp cloth if you receive the "ERR3" error. ERR3 is a contact error and your feet should ideally be bare and wet to achieve an accurate body-fat reading.
Step 5
Step off the scale and wait for it reset. Remove your shoes and socks and wet your feet slightly if you receive either the "ERR4" or "ERR5" errors, which means your body-fat or body measurements are out of range.
Step 6
Reset the scale if it doesn't work or you continue to receive error messages. Remove the battery and set the scale on a flat surface. Stand still on the scale for five seconds and step off. Re-install the battery and place the scale back on the flat surface. Place one foot on the scale until it displays zeros or dashes. Remove your foot and wait for the scale to turn off. Step back on the scale to weigh yourself.
Step 7
Replace the battery if you receive a "lo" or "bat" error.

Remove your shoes and socks and wet your feet slightly with a damp cloth if you receive the "ERR3" error. ERR3 is a contact error and your feet should ideally be bare and wet to achieve an accurate body-fat reading.

Step off the scale and wait for it reset. Remove your shoes and socks and wet your feet slightly if you receive either the "ERR4" or "ERR5" errors, which means your body-fat or body measurements are out of range.

Reset the scale if it doesn't work or you continue to receive error messages. Remove the battery and set the scale on a flat surface. Stand still on the scale for five seconds and step off. Re-install the battery and place the scale back on the flat surface. Place one foot on the scale until it displays zeros or dashes. Remove your foot and wait for the scale to turn off. Step back on the scale to weigh yourself

"EE" means that the scale has been overloaded. Try placing a small weight (i.e. 250g block of butter) on the scale and then turning the scale off and then on again with the small weight still on the scale. What this does is to try and re-calibrate the scale. If this doesn't work then I am pretty certain that the scales will need to be replaced. The scales in question do have a 15 year guarantee and you can try contacting Salter Housewares directly if you have your proof of purchase.

https://www.pricescompare.co.uk/q&a/ee-showing-on-screen.html

oUt2 means that it needs to be calibrated. I am not familiar with these scales so no sure if they can be re-calibrated.

My scale is doing the same thing and I can't find anything on how to fix it what a waste of money did you ever get this resolved?

How to calibrate when "out2" is shown.
With the power off andthe scale on a stable surface, hold "g" and press "on". Some number will show up, probably a negative number. Press the "on" button again and the scale should display "Zero". Wait until it says "200.0". Gently place a 200 gram weight on the scale and wait a few seconds. If your successful it will say "Pass" and your scale will work again, yay!

good day,
hope this link below will solve your problem.

kitchen

From the Taylor Site http://www.taylorusa.com/faq-scales

Here are the basic ERR messages and their meanings:

• Error 0: Initialization
• Error 1: Instability (scale is on an uneven surface ex: carpet)
• Error 2: Unit may have been jarred or unit was overloaded (customer went over the maximum weight capacity)
• Error 3: Contact error (Feet were not wet for Body fat reading, feet aren’t big enough to reach sensors)
• Error 4: Body fat is out of range
• Error 5: Water is out of range

I got an ERR2 message and now the scale doesn’t work. What should I do? The following reset procedure is used when the scale shows an err2, err, 0.0, inaccurate weight, or some other unusual error.

1. Remove the battery from the scale.
2. Sit the scale on a hard surface floor.
3. Step up onto the scale, stand still for about 5 seconds and step off the scale.
4. Re-install your battery.
5. Place the scale back on a hard surface floor.
6. With one foot only, place just enough weight on the scale for the display shows zero’s or dashes. Once you see zeros or dashes remove your foot.
7. Wait for the scale to turn off again.
8. Step up onto the scale for a weight.

If the reset is successful, you should receive a weight right away. If you continue to receive one of the error messages above please call our Customer Service department or contact us via email. You can also try the reset procedure a 2nd time. Sometimes the reset procedure will work the second time.