Factory reset when i turn it on fhere is a pause then the input dialog box blinks and then nothing.

If you have replaced the drain pump in your Bosch WAE24463 washing machine and it still doesn't finish programs and shows the error code F18, you can try a factory reset to see if it resolves the issue. Here's how you can perform a factory reset on your Bosch washing machine:

1. Ensure that the washing machine is turned off and unplugged from the power source.
2. Press and hold the "Start/Pause" button.
3. While holding the "Start/Pause" button, turn the washing machine's program selector knob to the "Off" position.
4. Continue holding the "Start/Pause" button for about 5 seconds.
5. Release the "Start/Pause" button.
6. Turn the program selector knob to the desired program and then press the "Start/Pause" button to start the reset process.

Please note that performing a factory reset will erase any custom settings or programs you have saved on your washing machine, so you may need to reconfigure them after the reset.
If the factory reset doesn't resolve the issue and the F18 error code persists, it's recommended to consult the user manual or contact Bosch customer support for further assistance. They will be able to provide specific troubleshooting steps based on the model and error code you are encountering.

Your TV could of had stopped working and you need to by a new TV.It would be more cheaper to by a new TV than to try and fix the TV that is broken.

Step 1 Press the "Power" key to wake the Kindle from Sleep mode. The Password prompt displays.
Step 2 Type your best guess at the password into the Password input box. Retype password guesses a total of four times. After the fourth incorrect password entry, the Reset dialog box opens asking if you would like to reset the Kindle Fire.
Step 3 Tap "OK Reset" to reset the device to original factory settings.
Connect the Kindle Fire to a wireless network and re-register the device with your Amazon account.
Tips

• Tap the "Show" option in the Password dialog box to display the password characters as you type.
• Visit the Amazon.com Reset Password page to reset your Amazon.com password (see Resources).

Warning

• Information provided in this article applies to the 1st generation Kindle Fire. Instructions may vary slightly or significantly for other models of the Kindle Fire.

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

IF YOU GET A CODE 12 WHICH IS THE BLINK PAUSE BLINK BLINK THEN THE TV THINKS THERE IS NOTHING WRONG WITH ITSELF. ARE YOU SURE IT ISNT CODE 22 BLINK BLINK PAUSE BLINK BLINK? THAT WOULD BE A CONVERGENCE FAILURE COMMON FAILURE FOR CRT REAR PROJECTIONS.

This sounds like a time out mode for no signal. there is a factory reset to factory sets. there is a way to do this in your manual. usually it requires a signal into the Antenna input.

I have the same TV and the error light code on my set is 22

The DM is fine if the led isnt blinking. Your set is going into protective shutdown. Try pressing the menu and the device/input buttons on the set both in together for 5 seconds to see if the set will blink a series of blinks pause then blink another series of blinks. Such as 2 blinks pause then 2 blinks, Then let me know what the blinks were and I will assist you with whats wrong

You should try a factory reset. Power off the printer. Hold the "pause" and "feed" buttons down while powering up. Allthe lights will blink and when they stop blinking, release the "pause" and "feed" buttons. This will factory reset the printer.

Hopefully you can read this. I downloaded entire manual from Zebra. This section is the feed button options to reset communications, calibrate, print configuration & also to do a factory reset. You will need to try the FACTORY reset. Basically while the printer is on you press & hold the feed button till it blinks 4 times in a row then release. It will blink 1 time then pause then it will blink 1-11 & pause then 1-11-111 then pause then finally 1-11-111-1111 then release. Each 1 represents a blink. I would attach the doc but system is too busy to allow right now.