I need the value for the network address property.

Hi,

STEP1: Print "Network Configuration Page"

• Make sure paper is loaded.
• Push the Setup Button on the all-In-one.
• Use the Down Arrow key to highlight the Network menu.Push Ok
• Push Ok again to select View Network Settings .
• Push Ok again to select Print Network Configuration page .
• A network configuration page will print.

STEP 2: Check the Printer Connectivity

• From the printed Network configuration page, note down the printer IP address, (example : 192.168.1.6).
  
• Click start, and then click "RUN".
• In the RUN box, type "CMD" press OK.
• In the command screen, type "Ping IP address" (Example: Ping 192.168.1.6). Hit Enter.
• You must get output similar to below.
  

Pinging 192.168.1.6 with 32 bytes of data:

Reply from 192.168.1.6: bytes=32 time=1ms TTL=64
Reply from 192.168.1.6: bytes=32 time<1ms TTL=64
Reply from 192.168.1.6: bytes=32 time<1ms TTL=64
Reply from 192.168.1.6: bytes=32 time<1ms TTL=64

Ping statistics for 192.168.1.6:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 1ms, Average = 0ms

STEP 3: Configure Port.

• Click on start >> Control Panel >> Printers and Faxes.
• Right click on printer icon, select "Properties".
• Click the PORTS tab on the top.
• Select your product under the Printer column, and then click Configure Port . The Configure Standard TCP/IP Port Monitor dialog box opens.
• Look in the Printer Name or IP Address box. This value should match either the MAC or IP Address on your network configuration page. If the values match delete the printer and install it again.
  
• If the values does not match,Click inside the Printer Name or IP Address box, and then type the appropriate value (IP address / MAC address) as listed in network config page.
• Click OK , and then try printing again.

Regards
Riztech

With wireless connections, there are at times brief disconnects. If you set your computer's ip address to a fixed value, this may help the problem. With a DHCP connection (not fixed) you could be getting a different address after one of the temporary disconnects causing the hang. Go to control panel, network connections, properties, then scroll down the window to the tcp/ip line , highlight it, then click the properties button. In the properties, click the use ip address button, enter a fixed ip address. If you are using a standard home address system, use 192.168.1.10 (if you have more than one computer, make sure each address is unique). subnet mask is 255.255.255.0, gateway is your router ip address, typically 192.168.1.1. Check your router information to be sure. You can use your router ip for the DNS server ip. If that does not work, check the DNS address provided in your router settings. Save all the settings.

See how that works, if it works, please leave feedback.

Good Luck

go 2 control panel and click network connection. then go to local area connection and click right mouse and see properties select tcp/ip address and click properties. then u will see ur ip address

You might be having a DNS problem. DNS (Domain name system) is responsible for changing the website name to the address (where the website is stored). You can try openDNS (www.opendns.com) The site can be confusing so here are the instructions. 1. Go to control panel > network connections 2. Choose the connection that gives you internet, right click on it and Click properties 3. Now select Internet Protocol (TCP/IP) and click properties 4. Check the box that says "Use the following DNS addresses" 5. Enter the following values (addresses) 208.67.222.222 208.67.220.220

Connect with an ethernet cable and find out the IP Address,
subnet mask, gateway, and dns,
by double clicking on Local Area Connection, click support, click details.

Enter these values for the wireless area connection

To set the values do the following:-

start -- > control panel --> network connections
right click on wireless area connection select properties
click on TCP/IP and press properties
Set to use the following ip address
enter the values from wired connection

ignore any duplicate warning messages

Thiswill resolve the issue, I have used it many times.

I have fixed this problem many times by entering just the gateway in the TCP/IP properties or all values as static e.g ip address, subnet mask and gateway as follows:-

Limited Connectivity | wireless network

Connect with an ethernet cable and find out the IP Address

Also note the Subnet Mask, Gateway, and Primary and Alternate DNS values

To get these :-

1. Double click on Local Area Connection under Control Panel --> "Network Connections"
2. Click "Support" --> Click "details"

Enter these values for the wireless area connection like this :-

1. Click "Start" -- > "Control Panel" --> "Network Connections"
2. Right click on "Wireless Area Connection" --> select "Properties"
3. Click on "TCP/IP" (in th middle box) -- > Click "Properties"
4. Click "To use the following ip address"
5. Enter the values you got from wired connection above
6. If you get any duplicate warning messages ignore these

This will resolve the issue, I have used it many times

There is no way to change the MAC address, but you can make Windows tell the system it has a different address that might fool your other program. Follow the instructions below.
Change the MAC address in Windows

1. Go to Start -> Control Panel. Double click on Network Connections (inside Network and Internet Connections category in Windows XP). The, right click on the active network connection with network adapter that you want to change the MAC address (normally Local Area Network or Wireless Network Connection) and click on Properties. Above steps work in Windows XP, Windows 2000 and Windows Server 2003 . For Windows Vista, access to NIC’s properties is from Control Panel -> Network and Internet -> Network and Sharing Center -> Manage Network Connections.
   Alternatively, if you already know which network adapter that’s responsible for your network or Internet connection, go to Device Manager and open the properties dialog by double click on the NIC itself.
   
2. In the General tab, click on the Configure button.
3. Click on Advanced tab.
4. In the Property section, select and highlight Network Address or Locally Administered Address.
5. To the right, “Not Present” radio button is by default selected as value. Change the value by clicking on radio button for Value:, and then type in a new MAC address to assign to the NIC. The MAC address consists of 6 pairs of numbers (0 - 9) and characters (A - F) combination. For example, 88-17-E8-90-E2-0A. When entering the new MAC value, omit the dash (-), for example 8817E890E20A.
   
6. Click OK when done.
7. To verify the change of MAC address, go to command prompt, then type in one of the following commands: ipconfig /all
   net config rdr
   
8. Reboot the computer if successful to make the change effective.

Dear you havent mentioned that you are on wireless or on Lan.
any way... issue is that your both systems have the same ip addresses and now you have to change ip address of any one of them..
i recommend you to change ip address of your desktop computer.

here is the way to change it...

1. Click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections.
2. Right-click the network connection that is connected to the private ICS network, and then click Properties.
3. On the General tab, click Internet Protocol (TCP/IP) in the This connection uses the following items list, and then click Properties.
4. On the General tab, click Use the following IP address. Configure the entries as follows: (if the option is selected that "obtain the ip automaticaly" then leave dont follow the given instructions and msg me again)
   
   • IP Address: . just change the last value of your ip address. say its 192.168.1.20 .. change the last value to any other two digit value..
   leave the other configurations as it is.
5. Click OK.
6. Click Ok

Now try it..


Rate me if you think it helps you..

best regards,

Tanveer Ahmad Khan

1. Go to Start >>> Control Panel and double click on Network Connections.
   
2. Right click on the Network Connection you want to change.
   
3. Under “General” tab, click on the “Configure” button
   
4. Click on “Advanced” tab
   
5. Under “Property section”, you should see an item called “Network Address”
   
6. On the right side, under “Value”, type in the New MAC address you want to assign to your NIC.
   
7. Reboot