How to remove bearing for cutter wheel - Vermeer BC1230A 12in Brush Chipper

drive belt loose
wheel bearing
cutter blades shaft bearing/ s seized up from rust hand brake stuck on and not releasing

3/8 allen wrench or hex socket,pry bar to get caliper off,screwdriver and hammer to get off dust cover,side cutter to remove cotter pin, channel pliers remove nut then pull the rotor off grease bearings and reinstall in new rotor.

Could be the same like front,can be four bolts,go to parts store ask for bearings you will see,same cars has no hubs.

pull the pulley off and in the housing there should be a circlip that you remove then the spindle and bearings come out. check which way it comes out as it may come up and out in which case you will have to take off the cutter disc/blade mount.

Your spindle is bent or warp. replace the whole spindle that is including the bearings. make sure you know how to tight the bearing.
With the right high temp. grease tightten it all the way and back it up 1/8 turn and put the new cutter pin.

They are hard to remove and replace. I have done hundreds of these. The best tool to use would be a pair of wire cutters or side cutters. The will grip the pin for removal and re installation. Grab the pin at the base and push the side cutters down to pry the pin out of the wheel. The best way to do it is remove the wheel. Unplug the unit first, then squeeze the two tabs in the middle. The wheel will then lift off. Take a picture of it first so that installation will be easy. Let me know if you need any more assistance.

a double wheel pizza cutter is a pizza cutter that has 2 wheels - one behind the other. The advantage of the two wheels is that they go through the pizza in one motion and you don't have to go back and forth to get a clean cut through the pizza.

You are looking at a major disassembly to get at the cutter head bearings, everything is built around the cutter head. The motor drives the cutter head on one end of it and the cutter head drives the rollers at the other end. Most of the components have to be removed to get the cutter head and it's bearings out. You can go to www.ereplacementparts.com and do a search on your model number for a good breakdown of your planner and see what you need to remove to get at the cutter head and it's bearings.

SECTION 204-01: Front Suspension 2000 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/18/2003 Wheel Bearing
Special Tool(s) Installer, Wheel Hub Bearing Cup
204-023 (T73T-1217-A) Remover/Installer, Bushing
204-180 (T93P-5493-A) Installer, Drive Pinion Bearing Cup
205-140 (T80T-4000-F) Adapter for 303-224 (Handle)
205-153 (T80T-4000-W) Puller, Bearing
205-D064 (D84L-1123-A) Installer, Wheel Speed Sensor Ring
206-054 (T93P-20202-A) Removal

1. Remove the wheel knuckle. For additional information, refer to Wheel Knuckle in this section.

1. NOTE: When removing the hub from the wheel knuckle the bearing will be destroyed. The bearing inner ring will be on the hub and the bearing outer ring will be in the wheel knuckle.
   Using the special tools, remove the wheel hub from the wheel knuckle.

1. CAUTION: The special tools must be used to prevent damage to the hub. If the hub is damaged a new hub must be installed.
   CAUTION: Do not use heat to remove the bearing inner ring.
   Using the special tools, remove the bearing inner ring from the wheel hub.

1. Remove the circlip from the wheel knuckle.

1. Install the old bearing inner ring.
   1. Install the bearing cage on to the bearing inner ring.
   1. Install the bearing cage and inner ring assembly to the wheel knuckle.

1. Using the special tools, remove the bearing outer ring from the wheel knuckle.

Installation
CAUTION: Avoid any impact on the wheel speed sensor ring.
CAUTION: Make sure the wheel speed sensor ring is clean.
CAUTION: Avoid any contact between the wheel speed sensor ring and a magnetic surface.

1. CAUTION: Make sure the wheel bearing is installed into the wheel knuckle with the wheel speed sensor ring, colored black, at the wheel speed sensor end of the wheel knuckle.
   Using the special tools, install the new wheel bearing to the wheel knuckle.

1. NOTE: Make sure the circlip does not cover the wheel speed sensor.
   Install the circlip to the wheel knuckle.

1. Using the special tools, install the wheel hub to the wheel knuckle.

1. Install the wheel knuckle. For additional information, refer to Wheel Knuckle in this section.

just keep in mind brakes are a saftey item.
if you could have both rear wheels and drums off then dis assemble linings then remove wheel cylinder and replace, assemble up the same as other side to copy. borrow some maintenance repair books from library or google procedures from manuals with drum brakes all have same principals.some front wheel drive vehicles have wheel bearings that need repacking with grease when removing drum and hub as one and more importantly have the do up nut by feel rather than torque up to setting hub nut and some drums come straight off from hub leaving bearings and hub on vehicle.
tools
garage jack, saftey stands, wheel brace to remove wheel nuts, brake hose clamp, side cutters(pliers),flat head screw driver, hammer, socket set, spanner set,mostly 10mm ring and open ended spanner for wheel cylinder