Water inlet error - LG WM-1832C Front Load Washer

LG DISHWASHER ERROR CODES AND DESCRIPTION MODELS LD 1420W2 D1420WF LD...

ERROR CODES; FAULTS & REMEDY ERROR DISPLAY [IE]
Inlet error.
Condition: Not reached to the normal water level in spite of 10 min. water supply.
Possible causes:

1. The Water Tap is not opened.
2. The Inlet Hose is twisted.
3. The Filter of inlet valve clogged by impure water.
4. The Inlet Water Valve is normal ?
5. The water pressure is very low. ( below 0.5 kgf/ )
6. Inlet valve is blocked by safety device for leakage sensing.(In case of Inlet Valve).

Remedy

• Open the Water Tap.
• Repair the Inlet Hose.

1.Close the Water Tap.
2.Unscrew the Inlet Hose (Inlet Valve side)
3.Clean the Filter of Inlet Valve.
> Replace or repair the Inlet Valve.
> Check the water remain on the base.
1.Check the point of damages and repair or replace the related parts.
2.Disconnect the inlet hose to dishwasher to unlock the safety valve.
ERROR DISPLAY [OE]
Drain error.
Condition: Not fully drained out in spite of 5 min. drain operation.
Possible causes:

1. The Filter clogged.
2. The Drain Hose twistec or blocked.
3. The Drain Pump/Motor or circuit is troubled.

Remedy

• Clean the Filter.
• Remove the cause of twist or block.
• Replace the Drain Pump/Motor or repair the Circuit.

ERROR DISPLAY [E I ]
Leakage error.
Condition: The water level in Tub goes down during operation.
Possible causes:

1. Water leakage in Hose connections.
2. Water is leaked by damages.
3. Impeller of the washing Pump is worn away.
4. The Thermal Protector of the washing motor is functioned

Remedy

• Replace the connections of Hose.
• Check the point of damages and repair or replace the related parts.
• Replace the washing pump.
• Check the applied voltage.

ERROR DISPLAY [ F E ]
Excess error.
Condition: Excessive water is supplied than normal water level.(Automatically drain Pump operated.).
Possible causes:

1. The Inlet Valve is troubled.
2. The Air Break is troubled.
3. The Sensor Assembly is troubled.
4. The Controller is troubled.

Remedy

• Replace the Inlet Valve.
• Replace the air breaker.
• Replace the sensor assembly.
• Repair or replace the controller.

E10 No cold fill detected - washing machine does not fill

• Check mains water pressure
• Check inlet hoses for kinks
• Check inlet filter
• Check water inlet valve
• Pressure switch fault
• Wiring fault

E11 Not hot fill detected - washing machine does not fill

• Check mains water pressure
• Check inlet hoses for kinks
• Check inlet filter
• Check water inlet valve
• Pressure switch fault
• Wiring fault

Message = E2
Error = OVERFLOW ERROR
Cause & Solution =
The water is supplied continuously due to an defective inlet valve. Change the valve inlet.
The valve inlet is normal, but the water level sensor Change the water level sensor
(sensor pressure) is low. (sensor pressure).
The drain motor does not work - Test and if faulty change the drain pump


Message = E9
Error = SENSOR PRESSURE ERROR
Cause & Solution = The water level sensor is faulty. Change the water level sensor. (remove pressure tube and blow through it to make sure it is clear first)

Hi.

F20 means that there is a water inlet problem:

Reasons for error F20:
(Water Inlet Problem-no water or insufficient
water supply) Select PAUSE/CANCEL twice to cancel the cycle
Unplug washer or disconnect power.

Check the following: Are water faucets completely turned on?
Are screens at inlet hose connection to washer
clogged? Are water inlet hoses kinked? Are water inlet hoses frozen?

If that does not help inlet valve, pressure switch and control module must be tested. The defective part must be replaced.

Here the tech sheet.

Regards.

Ginko

Hi

Error code IE on LG dishwasher means Inlet error. This error comes up when the Water Supply Tap is closed or Water Supply is shut off. If water supply is turned on then make sure that the Inlet Hose is not kinked and water Pressure is not low (should be above 10 psi). Next thing to check for is Water Inlet Valve, measure the electric resistance of Inlet Valve. (950-1300 ohms) Make sure the filter of Inlet Valve is not clogged.

Hope this helps... Please post back for further assistance.

Daniel

It is an inlet error. Normal water level is not reached after 10 minutes.Check the following:

1. The Water Supply Tap is closed.
   
2. The Water Supply is shut off.
   
3. The Inlet Hose is kinked.
4. The Water Pressure is very low. (below 10 psi)
5. The filter of Inlet Valve is clogged by impure water.
6. The Hall sensor is OK.
7. The Impeller of Air Guide is bound

Remedy:

1. Take action on Water Supply device.
2. Measure the electric resistance of Inlet Valve. (950-1300 ohms)
3. Clean the filter of Inlet Valve.

1E error is Not reached to the normal water level in spite of 10 min. water supply
POSSIBLE CAUSE REMEDY FOR ERROR OCCURRENCE The Water Supply Tap is closed. The Water Supply is shut off. The Inlet Hose is kinked. The Water Pressure is very low. (below 10 psi) Inlet Valve is OK? The filter of Inlet Valve is clogged by impure water. The Hall sensor is OK? The Impeller of Air Guide is bound.
Remedy Take action on Water Supply device. Measure the electric resistance of Inlet Valve. (950-1300 ) Clean the filter of Inlet Valve. Check the frequency of Inlet Water by the Test Mode. Replace the Air Braker.

troubleshooting with the F20code what it says in the trouble shooting section:

Ff20 (water inlet problem, no water or insufficient water supply)

Select stop twice to cancel the cycle. Unplug washer or disconnect power.

Check the following:

Are water faucets completely turned on?

Are screens at inlet hose connection to washer clogged?

Are water inlet hoses kinked?

Are water inlet hoses frozen?

Plug in washer. Re select cycle and press start.

IE is inlet error, displayed when "Not reached to the normal water level in spite of 10 min. water supply"

Possible cause:

• The Water Supply Tap is closed.
• The Water Supply is shut off.
• The Inlet Hose is kinked.
• The Water Pressure is very low.(below 10 psi)
• Inlet Valve is OK?
• The filter of Inlet Valve is clogged by impure water.
• The Hall sensor is OK?
• The Impeller of Air Guide is bound.

Remedy:

• Cut power by tripping circuit breaker or unplugging power cable for ten minutes.
  
• Take action on Water Supply device.
• Measure the electric resistance of Inlet Valve. (950-1300 )
• Clean the filter of Inlet Valve.
• Check the frequency of Inlet Water by the Test Mode.
• Replace the Air Braker.