Advent tv LC15y26 wont connect with stalite box

1157 1027 1011
1298 1081 1080
Check these codes. If you wish to get more, check these sites. http://remotesearch.blogspot.com/
http://electrohelponline.blogspot.com/
Pull up previous posts by its left sidebar, or type in the brand name and model number to of your set, to its search box, and press 'Enter' or view it in Mosaic / Timeslide option.

If you are saying no red: The model indicated here Recoton Advent Advent Q1435A TV is a 14 inch set.

first it may be cheaper to replace than repair--That said if no red look to the small circuit board at end of picture tube (it plugs onto the tube).

It will have either individual output transistors or a single IC.

What (if only one color missing) I would look at is the bottom side which faces to the rear---a circle of solder connections--possible one is broken--there will be one for each red, green, and blue--not always easy to see but if any of the solder connections look cracked or even broken loose-----

Does your TV have an S-VIdeo input? Does your TV have a DVI input?

What model of Advent laptop?

Does your laptop have a S-Video output socket (looks quite similar to a PS/2 mouse-socket) ?

Does your laptop have DVI-output?

Hi -

If you have a cable TV line connected directly to the TV, an antenna or a cable box connected by coaxial cable, I would suggest running the automatic channel scan (AUTO-PROGRAM) again:

1. Press the AV key on the Advent remote control repeatedly until TV is displayed in one corner of the TV screen. If you don't have the Advent remote, use the TV/AV button on the front of the TV.
2. Press the MENU key on the advent remote or the front of the TV to open the on-screen menus.
3. Use the CH+/- keys on the remote or on the front of the TV to highlight PRESET then press VOL+ to select.
4. Use the CH+/- keys on the remote or on the front of the TV to highlight ANTENNA then use the VOL+ key to select either AIR (for antenna) or CABLE.
5. Use the CH+/- keys on the remote or on the front of the TV to highlight AUTO-PROGRAM then press the VOL+ key to start the automatic channel scan.

Once the channel scan is complete, the TV should automatically return to viewing the first channel found during the scan. Do not press the MENU key during the scan or the scan will not complete.

If you are using a cable/satellite receiver and it is connected to the TV by any means other than a coaxial cable, you do not need to run the channel scan. You should simply select the correct AV input using the AV key on the remote or the TV/AV key on the front of the TV (see step 1 above).

If you have done all of the above and you are still unable to get the channels on your TV, please post back for further assistance. You can reply to me by clicking on "Add a Comment" below your question. Please let me know whether you are using a direct cable line, antenna or cable box, etc.

Regards,
BElectric

Yes you will most certainly need a converter box. At Radioshack you should still be able to get the piece that you would attach the spliced wiring to.One side of the piece I'm talking about has a screw for each one of the Y shaped spliced ends to attach to. Sometimes there are two places to attach things and sometimes there are four so buy the one that best fits your needs. Then the other side of the piece has the male part that will attach to the female antenna in part on the converter box. Then a cable goes from one of the outs on the converter box to one of the ins on the television.

have you connected the advent surround system to the tv so it plays what the tv is displaying or do you have the advent connect to the tv reciver (sky, tevo, whatever)

Use the TV's remote-control to select "input" from the S-Video port, rather than from the TV's own tuner (or from your cable-box).

Hi

you have defective power oscillation in Hot area, and you have defective vertical output change the vertical output...

Thanks!

You can also search for codes with out list.
switch on the power button manualy.
Press the program button on the remote press tv button and then channel up or down button. then the led on your remote will start blinkoing. when it reaches the correct code your tv will be switch off .then press program button once more or your remote.
Please try this option....

hi, you can now buy a box that can take upto 5 hdmi inputs to plug into your tv, i'm sure your local game shop will supplie them, if not search on ebay. hope this helps