Need remote control code for Polaroid fml1511 tv for directv rc24 remote?  All codes provide from Directv do not work have tried numerous codes, mitisutbish, toshiba, and all polaroids.  Looking for help.

This a link to the direct TV rome code look up should be able to give you what you need

Direct TV Remote Control Code Look up

Don't forget to Rate if I helped you :-)

Ask the remote code search engine. They will figure it out for you.

Here is the list from Direct tv with your Polaroid TV Codes:
Polaroid 10765, 10865, 11262, 11276, 11314, 11316, 11326, 11327, 11328, 11341


***Note: White remotes RC16, RC23, and RC24 may not be programmable to some later TV models

I hope this helps,
David

If my solution helped please rate accordingly

Programming DIRECTV Remote
1. Locate the DIRECTV Receiver's brand and model number
(on the back or bottom panel) and write it in the
spaces below.
2. Locate the 5-digit code for your DIRECTV Receiver (see
page 10).
3. Power on the DIRECTV Receiver.
4. Move the slide switch to DIRECTV icon.
5. Press and hold in the MUTE and SELECT keys until the
green light under the DIRECTV icon flashes twice and
then release both keys.
6. Using the number keys enter the 5-digit code. If performed
correctly the green light under the DIRECTV icon
will flash twice.
Magnavox codes:
11454, 10054, 10030, 10706, 10179, 11254

7. Aim the remote at your DIRECTV Receiver and press
that the power key once. The DIRECTV Receiver should
turn off. If it does not turn off, repeat steps 3 and 4, trying
each code for your brand until you find the correct
code.
8. For future reference write down the working code for
your DIRECTV Receiver in the blocks below:

Once you have programmed the DIRECTV remote control for
your TV, you may want to activate the TV Input button.
1. Move the slide switch to the position under TV icon.
2. Press and hold the MUTE and SELECT keys until the green
light under the TV icon flashes twice and then release
both keys.
3. Using the number keys enter in 9-6-0 (The green light
under the TV icon will flash twice)
You now have the ability to control the Input select feature for
your TV.

1. Turn on the TV or component. Insert a tape or disk if
applicable.
2. Slide the MODE switch to the TV, AV1 or AV2 position,
as desired.
3. Press and hold the MUTE and SELECT keys at the same
time until the green light under the selected switch
position flashes twice, then release both keys.
4. Enter 9-9-1 followed by one of the following fourdigits
5. Press PWR, or other functions (e.g. PLAY for VCR) you
want to use.
6. Point the remote at the TV or component and press
CHAN+. Repeatedly press CHAN+ until the TV or
component turns off.
NOTE: Every time CHAN+ is pressed the remote
advances to the next code and power is transmitted
to the component.
7. Use the CHAN- key to step back a code.
8. When the TV or component turns off, stop pressing
the CHAN+ key. Then, press and release the SELECT

White remotes RC16, RC23, and RC24 may not be programmable to some later TV models.

The codes for RCA televisions are as follows

11447, 10047, 10019, 10679, 11247, 11547, 10090, 11147, 11047, 11347, 10018.

here is a link to the DirectTV instruction page for remote set up and instructions if you are unable to find the correct code.

http://satex.com/directv/remote_codes.html

Hope this helps :)

Slide top button on remote to tv. Press and hold mute and select button until the green light on the remote blinks twice. Then press 991. Then press 1. Then press the tv power button once. If the tv doesn't respond hit the channel up button on the remote. If that works press select to store the code and slide the switch back to the left. If it doesn't work keep hitting channel up until it does. It can take up to 30 minutes but it works.

I have the TLA-04011c and have yet to find a code. Out of curiosity, have yall? thanks