Set time on bowflex heart monitor - LTD Watch Bowflex Strapless Heart Rate Monitor watch

To reset your Timex 637 T5G951 WR 30 heart monitor, you can follow these steps:

1. Press and hold the "Mode" button on the front of the watch for three seconds until the watch display shows "Settings."
2. Press the "Next" button on the side of the watch to scroll through the settings menu until you reach "Reset."
3. Press the "Mode" button to select "Reset." The display will show "Yes" and "No."
4. Use the "Next" button to scroll to "Yes," and then press the "Mode" button to confirm.
5. The watch will reset and return to the time display.

Note: Resetting your Timex 637 T5G951 WR 30 heart monitor will erase all your saved data and settings, so you will need to set it up again after the reset. If you need to keep your data, consider transferring it to another device before resetting the watch.

Language settings should be specified in your user's manual.
See General Settings, Page 12-13
Read it. If you don't have one, download it from here

http://www.polar.com/e_manuals/FT7/Polar_FT7_user_manual_English/manual.pdf

See video

Polar FT 7 Heart Rate Watch review

Polar FT7 Heart Rate Monitor


Polar FT7 Fitness Heart Rate Monitor HeartRateMonitorsUSA com Polar FT7 Review 2015 Best Heart Rate Watch

For all those who lost their Polar Heart Rate Monitor manuals. Follow this link, fill in the details and get manual. Plenty of other Polar product info and support on this site.http://www.polar.fi/en/support/downloads?product=&category=User+manuals

In time mode, hold set (bottom right button) to change date and time. The selected (flashing) item can be changed in one direction only using the up (top right) button. Press set again to cycle through each item until desired settings are chosen.
In stop watch mode, the up button starts and stops the stopwatch, the set button will take a split time while the time is running. To reset the stopwatch, press set once while the time is stopped.
In alarm mode, the up button turns the alarm on and off. There are three alarms available. To cycle though alarm times, press set. To set an alarm, press and hold set until the time flashes, then set the alarm time using the up button, cycle through hour and minutes using the set button. When finished, press set again.
Timer mode. To set the timer time, press and hold set until the time flashes. The timer goes up to 23h:59m:00s. You cannot set seconds. Once set, the timer can be started and stopped using the up button. There is no reset for the timer, to start a new timer the time must be manual changed again.
To check heart rate, press and hold mode until PUL is shown, place two fingers, one each on the top and bottom metal contacts for 6-10 seconds to get reading (This works best when not in motion).

Try this:
search-manual-online.com/bowflex-precision-xt-heart-rate...

Press and hold the reset button, for 5 seconds, while in Time mode. the heart monitor will reset and the symbol reappear on the screen

That is such a specific type of watch you will have to contact them at the following link:

https://www.heart-rate-watch.net/contact-us?osCsid=18b0055ce5db1b2b4eba5e48cb5eeb1e

Best wishes

To get a manual for your monitor, go to "sportline.com",

Select "products" and then "see products" in heart rate monitors.

Go through the list of models to find yours and then click on "learn more".

Details of the monitor will be shown and you then click on the tab marked "manual".

Download your manual.

This is really easy to do yourself. Get a CR1632 battery, unscrew the four screws on the back (dont tip the watch as there is a small spring in the watch), unclip the metal band holding in the old battery noting the way 'round the battery is in (minus side up), pop in new battery and push clip back down, when re-fitting the back make sure the spring mentioned earlier lines up with the white sticker with a hole in it on the inside of the watch back, screw down the back. After you have re done all your settings you may need to re-aquaint the watch with the strap, to do this put on the watch and strap, set the heart monitoring going, bring the watch up close to the 'Polar' logo on the chest strap until the time is displayed, should now be all set up.

Andy

Yes, you definetely need battery replacement.
As the hart rate monitoring is most sophisticated part of the device, it has more IC (Integrated Circuits) than any other features.
More IC's means more power is needed, so, if the heart rate monitor is starting to malfunction, that's the very first sign of underpowered battery.
Find your nearest watch repair shop and ask for battery replacement.

Do not forget to rate, please.