At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If it is just the glass, the back plate the glass sticks to is only clipped in. You will probably need to smash the old glass when you GENTLY lever the old one out. Check the back of the plate as the heated versions have a wire connected to it. The picture is for a 2008 but the set up is exactly the same.
To replace the whole assembly you need to remove the trim and the door card. The bolts mount the housing from the inside through the door. The trim and door card will be held on with small screws and push in clips. Some of the screws can be tucked out of sight so make sure you don't miss any. The push clips should 'pop' out if GENTLY levered out.
Hi,If you want to cut glass left over form old project or somebody gave it to you for what ever reason the first thing you need to do is make sure that the glass is plate glass becouse if you try cutting tempered glass its going to blow in your face.
Usually tempered glass has a stamp somewhere in the corner which proves that is tempered and the company that tempered it. After you know for sure that your glass is plate glass you need:
1.Safety glasses
2.Glass gloves
3.Glass cutter
4.Straight edge
5.Cutting table or flat surface covered with felt or short hair carpet
6.Measuring tape
7.Clamps (to hold your straight edge while you score the surface)
The thing is you dont cut glass,you score it with the cutter and then brake it.Please let me know what kind of glass are you going to cut so I can be more specific.
Thecoverplateisabove the glasswhite surfaceof the scanner.If thisisthe samedirtystainswill come outon copies. Theglassmust be clean. By feedingthe original documentsthrough the ADF,the scanner lampis no longerthe pathto scan,the ADFis responsible forpassing theoriginaldocumentover thescanner, whileit remainsstillplacedon the sideunder athinglassistoalargeglass side.Thisalsomust be clean,otherwise youwill be black linesoneach pointor spot onthe glass. Good luck...
not a train smash, locate screws to seperate the two door halves to allow access to the inner glass. remove screws and plates holding the broken glass. clean then place new one in possition and tighten screws comfortably tight.(dont over do it).Reassemble door.
Removal NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar. All exterior mirrors
Position the exterior mirror glass in the full down position.
Grasp the top and carefully pull the exterior mirror glass away from the mirror housing.
Disconnect the electrical terminals (if equipped) and remove the exterior mirror glass.
Power exterior mirrors
Remove the jack pins from the exterior mirror glass backing plate.
Use pliers to grasp the jack pins at the base to remove.
Installation Power exterior mirrors
Remove the sealing boots from the exterior mirror motor.
Install the jack pins in the sealing boots.
Install the jack pins and sealing boots.
Hold the legs of the jack pins and push the jack pins back into the exterior mirror housing.
Install the sealing boots so the boot shoulder is under the mirror collar and turn each jack pin until the head of the jack pin is aligned with the slots in the sockets on the backing glass plate.
All exterior mirrors
Place the new exterior mirror glass assembly down on a smooth firm surface.
Align the friction pins vertically to the exterior mirror glass backing plate socket and push down to snap the pivot ball into the socket.
CAUTION: Do not over heat the exterior mirror glass backing plate. Heat only until backing plate is warm to the touch. Using the special tool, warm the main pivot sockets in exterior mirror glass backing plate.
Loosely install the glass.
Connect the electrical wiring to the electrical terminals (if equipped).
Position the friction pins in the mirror housing.
Align the jack pin locating tabs to match with the mirror glass back.
Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
Press the mirror glass toward one of the jack pins until snapped in place.
Repeat for second jack pin.
Power exterior mirrors NOTE: If the jack pins do not engage, they may not be aligned correctly. Remove the exterior mirror glass, align the jack pins to the slots in the sockets and repeat the installation procedure.
NOTE: The jack pin should click while manually adjusting the exterior mirror glass. Tilt the exterior mirror glass to the full outboard position and then press on the outer side of the class until the in/out jack pin snaps into the socket on the exterior mirror backing plate.
NOTE: The jack pin should click while manually adjusting the exterior mirror glass. Tilt the exterior mirror glass to the full down position and then press on the outer side of the class until the up/down jack pin snaps into the socket on the exterior mirror backing plate.
×