Bowflex TC5500 fuse for motor board. When staring the machine for work out, the motor kicks off then reboots. How do we order and replace a fuse?

www.treadmillpartszone.com

You must locate to side from the power switch you must find the fuse holder and replace the fuse with THE SAME SIZE+CAPACITY+VOLTAGE INDICATED FROM THE SAME FUSE.

Remember if the fuse is Blown again or continuing you have a short circuite in a) Transformer b) Main Motor c) Main Controller Board d) Faulty ground in your receptacel from the wall very carefully.
attached the block diagram that I did for to illustrate to person like you, good luck. sincerely.

If you wiah to get some details about treadmill error codes and solutions then check the following link
http://electro-medical.blogspot.com/

Hi Craig, this sounds like a motor temerature cut-out gets activated due to high internal heating, do you smell hot motor at all? These cut-outs are temp driven- opening at a set temp, and then reclose after cooling via the Circuit-Breaker theory of heated bi-metals ;o)
You can also contact jatinah electronics for further help if needed.
Good Luck!

I was having the same issue to a T. I called Bowflex tech support, they told me that without a doubt the main pc board that is under the treads needed to be replaced for $515. I then trouble shot myself and got it up and running in minutes for $0. Take of the plastic top from the pc board area, unplug the little clipped in 2 wire plug labelled Fan. It litterally says fan on the board and you can see 2 wires going right to the fan. Once that is disconnected try to Quick Start. It should work. You can either replace the little fan for $6 @ radio shack or run a fan your self simply by facing your own in the same area. Most people are running a fan for themselves anyway, just aim for both. Good luck.

Resetting the button with Stop +Speed by 10 sec.
However you must LUBE the deck belt AND rollers bearings. This happen because the lack of maintenance schedule, You must do it every 150miles aprox.
See the video

you must try to call them, for to fix this problem , is more easy.
God bless you

LUBE THE DECK BELT, INMEDIATELY THIS HAPPEN BECAUSE THE LACK OF MAINTENANCE, ACCORDING THE SCHEDULE MAINTENANCE, READ YOUR OWNER MANUAL OR DOWNLOAD FROM WWW.ICONSERVICE.COM
GOD BLESS YOU

1) test the power cord for open, break
2) see if there some animal, bid the some wires internal, and get touch with the chassins provoking the short in the machine.
3) replace the blown fuse inside, see the block
4) test the main switch for open or defective.
5) unplugg the machine and see if there c.breaker or fuse are tripp? if does the problem is the c.breaker from your home
6) do NOT use extension cord, and buy some detector spikes, glitch,transient.
God bless you

That model does not have a calibration option. You may want to download the operation manual from the manufacturer at bowflexcatalog.com, there is a product manual link at the bottom of the page.

Had my TC5000 for a year and this is the first time this happened. I use it everyday. Googled "Bowflex Teadclimber error codes" and found this link  download.dfxi.com/supportdocs/AM/Bowflex/BFX_TC135_AM_2008.pdf which is a pdf manual. 
I'm going to try this fix now, hope it works for you and me
Here's what it says for ERR LS:
Belts stop turning and “err LS” or “err OS” is displayed Calibration Re-calibrate machine using Owner’s Manual calibration procedure. Speed sensor 1. Cycle power off and on. 2. Put the machine in calibration mode (see Calibration procedure in Owner’s Manual) but do not start the calibration routine. 3. Remove right rear plastic cover to view LED diagnostics on control board. Caution: Machine is on. Current is active!! 4. Locate LED D on the motor controller board. LED may be lit or unlit. 5. Manually advance the treadle with your foot, and check if LED D is blinking. 6. If LED D is not blinking, then the speed sensor is not supplying a signal. Check that the speed sensor wire is plugged into the motor controller board, to the connection labeled “P1”. Check connection of speed sensor to jumper wire. Check speed sensor adjustment (use business card to set gap between sensor and pulley). If LED D still does not flash replace sensor. I/O cables If LED D is flashing when the belts are turning but err LS or OS persists check connections and for signs of visible damage to any of the three I/O cables. If no damage, check continuity using a multi-meter. If a multi-meter is not available contact customer service for replacement cables and further assistance.
Mike