Inverter Pure Sine Wave 1500w Inverter - Answered Questions & Fixed issues

how i can joint 4switch box to one lamp with inverter & main

ur battery exp.(if it is 3 or 4 year old)
ur inverter is over load

trivedi ji namaskar
please make sure your inverter is on auto mode and then contect immidetly to your service provider for maintenance inverter becuse its microcontroller systems is not working.
hope question,s answer
thank you.

I and welcome to FixYa. I am Kelly. If you have a single load at 1430 watts and possibly some other item using power figure your max working load at 2000W. I would recommend a 3000W inverter.

The problem your going to have with an inveter that size is a single battery is probably going to die an early death trying to keep up with it. Your prbably going to need to parallel a 2nd battery into your work vehicle.

This inverter is what I would recommend so that no matter what you did to it (6000W burst load) you are not getting it fixed or replacing it.

http://www.invertersrus.com/vec051d.html

At $329.00 it isn't cheap but you spend the money ONCE vs repeatedly.

Kelly

Get out of here!!!!

Sounds like one of two things are happening:

1. Microwave is drawing too much current, causing internal voltage monitoring circuitry in inveter to go into protection mode.

or

2. RFI from microwave is somehow being few into inverter causing similar circumstance.

Are you using the correct by-pass relay. These are specially made to be a break-before-make just to prevent what your describing.

Just connect it to the battery. Normally you do it via the power outlet formerly called a cigar lighter. https://www.google.com/search?q=3000+watt+inverter ..

See page 3-10 AC Transfer Voltage. See page 3-14 Charger LED. See page 3-16 Startup. See Page 4-1 Troubleshooting. It will help you. 975-0012-01-02 Rev A.book (unboundsolar.com)

The water has shorted it out. Water and electronics is a BAD mix. OLP (Overload protection indicator): Indicates the inverter will shut down due to a short circuit or overload protection. the inverter cools down, the indicator will turn off automatically. Feb 14, 2023

Pure Sine Wave (ISW) Inverters: Error Codes - Go Power!

gopowersolar.com https://support.gopowersolar.com > article > 241-pure-si... ..

Error E. OH (overheat power module) on a KEB F5 Inverter indicates that the power module is overheating. This can be caused by a variety of factors, including a malfunctioning cooling system, a faulty power module, or a problem with the wiring or connections. To troubleshoot the issue, you can try the following steps:

1. Check the cooling system for any visible signs of damage or malfunction, such as a clogged air filter or damaged fan.
2. Check the power module for any visible signs of damage or malfunction, such as burnt or damaged components.
3. Check the wiring and connections to ensure that they are secure and properly connected.
4. Check the F5 Inverter's fuse and circuit breaker to ensure that they are functioning properly.

If these steps do not resolve the issue, it's best to contact a professional repair service or the manufacturer for further assistance. They will be able to diagnose the problem and recommend the appropriate repairs. It's also a good idea to stop using the F5 Inverter until the issue has been resolved, as continuing to use it may cause further damage.

It's generally not recommended to run a KIPOR 3000TI Inverter without the Kipor 66284 DC receptacle. The DC receptacle is an important safety feature that helps to protect the inverter and any connected equipment from damage. If it has been removed, it's possible that the inverter may not function properly or may be at risk of damage. If the DC receptacle has been removed and you are experiencing issues with the inverter, it's best to contact a professional repair service or the manufacturer for further assistance. They will be able to diagnose the problem and recommend the appropriate repairs. It's also a good idea to stop using the inverter until the issue has been resolved, as continuing to use it without the DC receptacle may cause further damage or pose a safety risk.

If your Power Star W7 has a dead display and no output, it's possible that there is an issue with the power supply or the display itself. Here are a few steps you can try to troubleshoot the issue:

1. Check the power cord and outlet to ensure that the W7 is properly plugged in and receiving power.
2. Check the power supply for any visible signs of damage or malfunction.
3. Check the display for any visible signs of damage or malfunction, such as cracks or loose connections.
4. Try resetting the W7 by unplugging it and waiting a few minutes before plugging it back in.
5. Check the owner's manual for any troubleshooting tips or information on common issues.

If these steps do not resolve the issue, it's best to contact a professional repair service or the manufacturer for further assistance. They will be able to diagnose the problem and recommend the appropriate repairs. It's also a good idea to stop using the W7 until the issue has been resolved, as continuing to use it may cause further damage.

Most likely the battery volts are displaying correctly. There is a voltage drop on the battery due to its internal resistance, when you connect a supply the voltage drop is less. If you were to put a new battery on it it might reduce the voltage drop, as long as the battery is designed for the current load it's taking. If it's working I wouldn't worry, but if the voltage continues to drop with use I'd be thinking it needs a new battery. (Assuming the battery is charging correctly)

I may miss the point here. If the question is how to clear the error, page 57, item 4.7 Error Messages, of the KEB instruction manual may be of use. https://www.manualslib.com/manual/1293218/Keb-Combivert-F5.html?page=55#manual Here is information about the error code: KEB Error "E. OP" ERROR overpotential (voltage) 1 Voltage in the DC-link cicuit is too high. Occurs if the DC-link circuit voltage exceeds the permisible value. Causes: - poor controller adjustment (overshooting) - input voltage too high - interference voltages at the input - deceleration ramp to short - braking resistor defective or too small Given the very technical nature of the KEB, I lean toward referring to the manufacturer's support. There are quite a number of KEB YouTube videos and a number of supporting documentations available on the web. Perhaps the following will be of use if not an entire misdirection: https://www.kebamerica.com/elevator-support/ https://www.kebamerica.com/products/f5-inverter/

Hi, Please use the initial setup process to double check that you've not accidentally pressed a button and allowed the current issue. After you've redone the setup, please attempt to use your inverter again. Thank you.

Hi, Please contact ABB directly to get the passcode information. You can do this by calling 1-800-435-7365. Thank you.

replace batteries

There is no fault if you are measuring the voltage with no load.

250watts up., but compressor have motor and start up current surges are huge on compressors. and may take 500watts to get it going. see???? there is no way to know this in advance unless you own a Ampere meter (best is amp-clamp type) and measure it your self the peak current. this motor needs to start up under full compressive loads.