Pride Jazzy Select 6 Indoor Power Wheelchair - Answered Questions & Fixed issues

It is not uncommon for a controller to continue flashing while it is charging. However, the fact that your controller still flashes 7 after you have exhausted and repaired it suggests that there may be a deeper issue with the controller. It is possible that there is a problem with the battery, the charging port, or the circuit board. If you have exhausted all of the troubleshooting steps that you are comfortable with, it may be best to contact the manufacturer or a professional repair service for further assistance.

Question edited for clarity. Question moved form Car Audio to Pride Jazzy Select 6. 9 Flashes The park brakes have a bad connection. Check the left and right motor connections and wiring. Check to make sure that the power chair is not in freewheel mode.

jazzy select - Any electromechanical device requires ...

Videos as well https://www.google.com/search?q=jazzy+select+6+blinks+9+times& ..

Not one answer relates to this question duh !!!

No. You can lock the controller electrically. You need to check the operators manual for the procedure for the model of controller you have.

You have two good batteries in the green side, the red light means that one or both batteries are not fully charging. Try that set on the other side to confirm. Make sure the batteries and charger connections are clean.
Hope this helps.

Check to see if both motors are engaged. If not the problem, most likely controller has a short in the circuit board.

Yes. Change the potentiometer behind the throttle lever. It's probably 10 ohms. Try a lower resistance pot. It will run the battery down quicker though.

My tires squeak how can i fix the problem and what ... - Fixya

www.fixya.com > ... > Pride > Jazzy Select 6 Indoor Power Wheelchair

Apr 14, 2012 - my tires squeak how can i fix the problem and what can i use - PrideJazzy ... Question about Pride Jazzy Select 6 Indoor Power Wheelchair ... I have a mpv 5 hoveround wheel chair and I now have a flat on the front left tire.

[PDF]Jazzy Select Series Owners Manual - Pride Mobility Products

www.pridemobility.com/...jazzy/us_select_series_om.pdf

Pride MobilityJazzy Select 6 with Power Seat. JAZZY. SELECT SERIES. Including Models: Jazzy Select, Jazzy Select 6, and .... Battery charger for indoor use only. .... Take wide swings with your power chair's front wheels around any tight corners. ... desired, allow it to come to a complete stop by releasing the joystick, then push the ...

[PDF]Jazzy Select Series - Pride Mobility Products

I have repaired thousands of jazzys elec wheelchairs and never have seen a fire or melt down

There should be a place to plug the charger in on the front of the joystick. It is a round three pin connector

This is usually one of two things. You will need to pry the on/off button away from the joystick for inspection. Use a utility knife to get under the edge and pry it off. The back of the rubber button is coated with a material that conducts electricity so that when you press it, it makes contact with the surface under it which is also conductive. 1. For older chairs that get a lot of on/off use, this metalic coating on the back of the switch can wear away and not make good contact with the base. Examine the back of the on/off button for wear; you will see the rubber under the metalic coating if it is worn. Pressing around the edges of the button might work to get it on and off, or pressing harder. Otherwise, you need to paint on a new coating. Here is a site that sells that product. http://www.newark.com/chemtronics/cw2605/conductive-chemical-coating-3g/dp/00Z1875?mckv=sskjVGufT'pcrid'57087234861'plid'&CMP=KNC-GPLA 2. If you have spilled something on the joystick that has fouled the connection here, it will have a hard time making contact to turn on and off. Clean with alcohol and cotton swabs, let dry and see if that does the trick.

The controller stops the batteries when the voltage gets too low to prevent damage to the batteries and the elecrtronic components.

You have to disconnect the charger in order for the chair to move. It automatically removes power from the controller while the batteries charge.

A light touch on the joystick is first. If it remains difficult then have the joystick reprogrammed. Only a dealer is set up to reprogram a joy stick.

You may need to lubricate the wheels and where they pivot on the frame, otherwise that's the way they operate normally.

If your charger has a red and a green led on it when the green led lights the battery is charged. If you use it a lot during the day it may take 8 to 10 hrs or more to fully charge the batteries

Go to Pride's website and download the service manual. It's in there

Until the green light o the charger comes on or the charge meter shows one amp or less. If the batteries were drawn down too far the 5 amp charger will NOT recover the batery. In that case seperate the batteries and charge each one with an automotive battery charger.

Go to Pride's website. You can download the operators manual and the service manual there.

The number of flashes indicate the problem. Go to Pride's website to download the service manual. It will tell you what the flashes mean and how to fix it.