20 Most Recent LG WM-2277HW Front Load Washer - Page 8 Questions & Answers


dE is a door error, check switch, door alignment and wiring harness

LG WM-2277HW... | Answered on May 29, 2014


door lid assemble having some problem. may be megnet pice came out.

LG WM-2277HW... | Answered on May 29, 2014


Usually a sign that you are using too much detergent. Pull the drawer out completely and clean it out. The drawer and the casing

LG WM-2277HW... | Answered on May 29, 2014


have the outlet checked by an electrician or qualified person to be sure the ground wire on your outlet is properly connected or that you have a good working outlet

LG WM-2277HW... | Answered on May 16, 2014


Sorry to read about your problem, I hope this helps you out.

The error code FE refers to the fact that water is overflowing ( normally means the inlet water valve is stuck open and continues to let in water beyond the expected and/or sensed level.. so the water pump turns on to drain it and keep the level down. This kind of problem would probably warrant a a service call from a tech since the majority of troubleshooting would require diagnosing the failed component itself and is not something that I recommend you try.

There are too many pieces of hardware that have a direct impact on how this works and I highly doubt you want to play the shotgun approach..try this to see if it fixes the problem and if not..try that...

Before calling for service.. try this..

1. Remove or disconnect ac power from the washer..let it sit unplugged for at least an hour..then try washing 1 towel at the lowest cold water setting to see if that works ..if it does..repeat the process using only hot water.. if that works... then try the same test using warm water.. ( this test may help determine if the water inlet valve .,.either hot or cold is leaking through it)...
If you still get the FE test..call for service..

BTW..if only one of the two tests fails.. ( Hot water only generates an FE error.. then chances are the hot water inlet solenoid valve assembly is either sticking open or the controls to that are commanding it to remain open.

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question's. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful

LG WM-2277HW... | Answered on May 15, 2014


faf6576c-2025-4abf-8a71-f6e053a5c6df.jpg
I hope this is helpful

LG WM-2277HW... | Answered on May 14, 2014


The LE error indicates that the Controller is having trouble communicating with the motor.

The most common cause for this is if something gets wedged in and the drum can't turn freely. Try turning it by hand to make sure it is free. The next most common cause is if someone spins the drum moderately fast with the washer turned off. I.e. if you give it a spin to make sure their isn't a sock stuck to the drum.. To fix this, unplug the machine and turn the drum counterclockwise 4 full rotations followed by 4 rotations clockwise at low speed. Plug it back in and see if that fixes it.

If that's not it, then there is a sensor called the Hall Sensor that could be the problem. I've never had to replace one of these and can't comment further.

GL

LG WM-2277HW... | Answered on May 12, 2014


That is most likely from the belt on the drum. If you want to check that though take some of the dust and see if it is gritty feeling. you can check that by putting it on something smooth and setting something hard on top of it and moving the top object around. Or pinch it between fingers etc. The motor should be brushless because it is an AC motor.

LG WM-2277HW... | Answered on May 10, 2014


te is a error code for a bad thermister. it senses the temp of water in the tub. this needs to be replaced

If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

LG WM-2277HW... | Answered on May 09, 2014


I had the same error code along with the drum "freezing" up. The first unit that was delivered 2 years ago leaked water from the detergent compartment and they sent a second unit. I have only had this unit for 2 years and I am very disappointed in the LG product. LG was no help on the phone and I the only people that could service it were 45min away from were I live. I took the advice of a posting on this website that it could be a part called the sensor assembly (#6501KW2002A) and ordered it from an online electronics store (www.mcminone.com). To get to the sensor assembly, you first unplug and take off the back plate that has 4 small screws. Next, unscrew the big bolt in the middle and take off the hubcap looking part the bolt was securing. Next unclip the two sets of wires on the bottom of the circle you are looking at (the set of wires to the right are connected to the sensor assembly you want to replace). Next you will unscrew the 6 or so smaller bolts to take off the circular piece that the sensor assembly is snapped to. Take it off, unclip the old sensor assembly and clip on the new one – and reassemble. This worked perfectly for me and the part only cost $18 bucks plus shipping. When working, this product works well but I will not be purchasing any LG products in the future.

LG WM-2277HW... | Answered on May 05, 2014

Not finding what you are looking for?
LG WM-2277HW Front Load Washer Logo

2,568 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WM LG

  • WM LG

Most Popular Question

stop old water smell earthy odour in lg

  • Washing Machines
Loading...