Pride New Mobility Legend 4 Wheel Scooter - Page 3 - Answered Questions & Fixed issues
I have a pride cleberity x...when i plug in the
Sounds like wiring loom or simply the charger is broken. Do you get both lights on the charger or just the power light? Should be a 5 amp charger on those if im not mistaken. Best bet is to get a multimeter, disconect one wire from the one of the batteries and put your multimeter wires between the disconnected battery lead and the battery terminal from which you disconnected it. Put the multimeter on the the 10 amp setting and switch on the charger. See what the reading is. If its zero or very low, would more than likely indicate a faulty charger but still could be the loom or even the scooters main control box, as the charging loom is usuall connected through this. Hope this helps.
3/18/2010 12:16:43 PM •
Pride New...
•
Answered
on Mar 18, 2010
•
158 views
Lights work but scooter will not run
have you pressed the reset button .Also make sure the scooter is in drive before turning on the ignition. Another thing could be badly worn brushes on the motor or even a plug connector not fully home. The most common is not fully charged batteries. IF IT IS NONE OF THESE GET BACK TO ME PLEASE.
steve.
1/24/2010 5:55:40 PM •
Pride New...
•
Answered
on Jan 24, 2010
•
319 views
The wood in my seat is braking up and my seat
Hi I have looked and looked to fix your problem now what I would do is the first thing I would ring the company that made your scooter and ask them for the pattern for your chair and make it that way or undo it bit by bit and write down everything you take off and where it goes and get the design that way then you could ring someone that covers lounge chairs and seats etc and get them to make you a cover in the material that suits your needs eg if you sweat alot or if the material rubs on your back or legs and you get a rash what ever you like they usually have a sample list that they carry with them and you can see for yourself of what suits you. and the next thing is to contact this company
http://www.usmedicalsupplies.com/search.html?q=+4+Wheel+Scooter+seat they might be able to build you a seat at a good price I believe the best wood you could find for your seat would be hardwood
then I would use a waterproof decking oil over it as this would stop the wood from braking on you it is also mould proof and a lot of other features this oil has is great I just found out about it my self this oil will also protect your seat in extreme heat to stop it from splitting the waterproofing of this oil is great for snow,heat,mould,splitting,cracking etc as it is designed for patios etc but make sure if you do it yourself you cover your hole seat in oil even the parts that are going to be covered just in case your material splits then you wont have to worry about the wood getting damaged the decking oil ( which is what it is called here in Australia) has a garentee for 10yrs
so give that a go and please let me no if there is anything else I can chase for you or if you are stuck with somethin
Cheers
1/22/2010 11:56:04 AM •
Pride New...
•
Answered
on Jan 22, 2010
•
53 views
How to stop it
hi, the high pitch sound is telling you there is a error condition,
Make sure the free wheel lever ar the rear is disengaged.
Regards
GeWiz.
12/25/2009 1:30:53 PM •
Pride New...
•
Answered
on Dec 25, 2009
•
124 views
How do i remove the pride legend classic xl8 seat
hi, be careful here as it can make your back ache,
now there is a lever to the right of the seat, pull it up towards you and
turn your seat 90 anticlockwise, so the seats not facing the control panel, at right angles, you should now be able to lift the seat , take great care here if you have back problems in the past as some seats are quite heavy.
Regards
GeWiz.
12/13/2009 2:44:37 PM •
Pride New...
•
Answered
on Dec 13, 2009
•
1,241 views
How can i DE-RISTRICTED my SUKIDA DRAGONFLY
hi,
there are a couple of ways to do this ,
Upgrade the batteries to a higher amps say 40amps to 55amps etc,
but if the controller is say 70amps, more powerful batteries will not make it go any faster so you will need to also look at the motor controller.
first what is the rating for the installed motor controller ? can that be upgraded to more amps say from 70amps to 110amps etc however you must take care here that the motor can handle the extra amps otherwise you will burn it out,
Regards
gewizrepairs.co.uk
12/13/2009 10:38:24 AM •
Pride New...
•
Answered
on Dec 13, 2009
•
485 views
Scooter just stops light flashes 8times
hi, 8 flashes mean there is a issue with the motor according to pride, now you need to check the motor connections back to the motor controller, have you check the brushes to make sure they are not sticking inside the motor,
sometimes eight flashes can mean that the speed pot has moved slightly so it in the wrong position when you turn it on, experiment by pushing in the throttle lever and holding it there now turn on it on,
if this sort the problem , undo the throttle lever and relocate so it in the right position hwne you first turn it on.
Regards
gewiz.co.uk
12/2/2009 3:04:33 PM •
Pride New...
•
Answered
on Dec 02, 2009
•
281 views
I have a komfi-rider 6000 i,ve had it on charge
Is your charger light on - i.e. is your charger working? Otherwise you may need new batteries....but take a note of the details on the battery and search around on the net for generic ones - much cheaper than the original make!
11/29/2009 5:09:29 PM •
Pride New...
•
Answered
on Nov 29, 2009
•
256 views
Only one battery charging on mobility scooter
If only one battery is charging than you only have one good battery. You should have BOTH batteries load tested. If you have to replace one than you should replace both. If you only replace one battery then it will shorten the life of the new one.
11/10/2009 5:02:59 PM •
Pride New...
•
Answered
on Nov 10, 2009
•
88 views
My farther as just bought a gainsbough 4 wheel
No, it means the Electro Brake is not engaging 100%,
Check the motor under the seat, now you will see two thick wires come from the motor , Red & Black if you look to the side of the motor you should see two thinner wires leading to the side of the motor , those are the brake power leads, (depending on Model) , has the brake seized ? or are the wires not making a good connection, these wire should lead back to the motor controller , normally a black or blue box, that is the motor controller , check connections, depending again on brand and model.
Regards
GeWiz.
10/17/2009 9:08:08 AM •
Pride New...
•
Answered
on Oct 17, 2009
•
115 views
Electrical fault
Sounds like a problem with the circuit board under the speed pot,
It could be a loose connection and remember there can be a fuse under there.
Regards
Gewiz
10/2/2009 8:41:52 PM •
Pride New...
•
Answered
on Oct 02, 2009
•
250 views
Thumb lever alternative
hi, I have a thottle control that would work this , can you twist your wrist okay ?, go to ebay and look for electric scooters, normally three wires now goto the control panel where the charge indicator etc is and remove the cover then look for the three wires that come form the thottle part and replace with the twist grip wires , you may need to experiment to get it right but it can be done.
10/3/2009 10:54:30 AM •
Pride New...
•
Answered
on Oct 03, 2009
•
162 views
Not finding what you are looking for?