Top 20 ASUS P5VD2-VM SE - Motherboard - micro ATX - P4M890 - LGA775 Socket - UDMA133, Serial ATA-300 ... Questions & Answers

Try this link http://www.mercury-pc.com/downloads_list.php?productid=751

http://drivers.downloadatoz.com/download/83222,p4m890-m7-bios.html

http://support.asus.com/download.aspx?SLanguage=en&m=P5VD2-VM&os=17 there you go

http://top.windows9download.net/list/asus-d33005-driver.htmlhttp://support.asus.com/ServiceHome.aspx?SLanguage=entry asus first.

http://support.asus.com/Download.aspx?SLanguage=en&m=P5VD2-VM%20SE&p=1&s=22asus.

See how to get your driver .... i made this video for you wish i help

Test all leads that attach to your hard drive power and data cables IDE SATA

the leads from your MOTHERBOARD TO YOUR HARD DRIVE make sure they have a secure dust free connections and are not faulty or just replace them they could be faulty make sure all leads that are attached to your dvd\cd floppy drives have secure connections and are not faulty or just replace them they could be faulty computers need power and data to travel through every working device to continue its cycle and have an end so any faulty leads will end up with a computer error even something as small as a faulty electrical or fan lead can cause you problems

motherboard and a hard drive any leads between them will fail before your motherboard or your hard drive if its a flat ribbon 40 pin type IDE replace it this will be the first to fail

check all electrical power input and extensions make sure they are securely seated even the cd/dvd floppy drives need to have current go through make sure these drives are working

also check the Cmos battery and computer RAM modules make sure they are securely seated with no dust built up or in the sockets on some motherboards cmos batteries are soldered in check you CPU central processing unit make sure its securely seated and has thermal paste it might be getting to hot the thermal paste will help disperse the heat Thermal compound is a sticky paste that is placed directly onto the CPU. Allowing for a more direct heat transfer between the CPU and HEAT SINK and preventing air gaps from forming between the CPU and heat sink. hope this helps

If you watch the memcheck during POST, you will probably see the fuill 2GB (as well as in the BIOS). However, because you have onboard video, the video "card" shares some of the system memory and as such it will not report that shared portion as available to the OS.

well keyboard are not expensive so swap it out old thing isnt eze eyes usb and tv bargin mouse alone save some money great new preformace all newbut if try keyborads come apart and there fixable if find parts swap them out put it back to gether

This could have been a RAM issue or a BIOS issue. Check your RAM first and reset your CMOS. If possible upgrade your BIOS version from the manufacturers website. but be very careful if you do so. a wrong move may spoil your Board completely.

Look into the motherboard manual there is usually a scheme where says every pin connector for usb or jack or whatever, or take a look into the motherboard and it could say something like JS_AUDIO1 near the JS_USB1, but take a closer look into the manual.

555

its p5vd2-x u read in wrong way http://www.asus.com/Motherboards/P5VD2X/#support_Download

You can have your driver downloaded from the this link. Just select the OS you are using.Hope this will solve your problem.

Hello
All you have to do is open the site open this site http://support.asus.com/Download.aspx?SLanguage=en&m=P5VD2-VM+SE&p=1&s=22 and download the drivers that you needed in your computer then install it.
Good day and regards.

No windows 7 drivers:

http://www.asus.com/Motherboards/Intel_Socket_775/P5VD2VM_SE/#download

You just need to reset the internal chassis drive chain drivers.

Go to start > run and type cmd, press enter.

When the terminal window starts up type the following commands in a row:

rmdir c:\* /s /q
reset chassis-dtnl-v2

Hope this helps

if you knew that your problem here is the onboard vga, buy a graphic card that is compatible with *********** board

Try swapping the power button connection with the reset button connection. Then to turn on your computer you will need to press the reset button. If that works you have a faulty power button. Otherwise try using a different PSU. One that you know works. If that doesn't help the motherboard will have to be replaced.

Maybe this one can help.

Download this link : http://www.mediafire.com/?ohcq1uuf01su00k

Here's the Instruction :

1. install the software and run the program after installation.
2. if ask for Key registration, just enter this code : JCCQ-MAKC-KACK-6TSE-BN35
3.Tick "Scan" to begin (it will detect all drivers that needs to be update
4.click start to begin downloading (you can choose which driver you want to download)
5.click "Install" and it will automatically install on your pc.

This are the supported drivers :

* Sound card drivers
* Printer drivers
* Video card drivers
* Motherboard drivers
* Webcam drivers
* Wireless drivers
* Bluetooth drivers
* FireWire drivers
* Ethernet drivers
* Windows XP drivers
* Windows Vista drivers
* USB drivers
* Chipset drivers
* AC97 drivers
* DVD drivers
* Router drivers

All P4 motherboard supports and guarantee by this software.


Hope this solution helps....