20 Most Recent
Remington Electric Chain Saw - Page 4 Questions & Answers
What kind of oil or oil mixture do I need to use
Hi brown9148..
The only oil you need for your electric chain saw is "Bar and Chain" oil...specially formulated oil sold at Loews,HomeDepot,Ace Hardware, Auto parts stores,etc...
You use this oil to lubricate the chain and bar of your chainsaw when you are using it.
It will go into the oil tank and auto feed to the chain and bar...but keep a check on the oil level to make sure it is being used.
Refill tank when needed.
Please take time to rate me
9/24/2011 6:07:54 PM •
Remington...
•
Answered
on Sep 24, 2011
Do you have to mix
Hi sullivan6451....
You do not mix oil and gas on an electric chain saw...
The only oil you will use on the chain saw it "Bar and Chain" oil...specially formulated for the use on the chain and bar on your electric chainsaw...
You can purchase the oil at any Lowes,HomeDepot,Ace Hardware...etc..
Please take time to rate me
9/24/2011 2:14:01 AM •
Remington...
•
Answered
on Sep 24, 2011
What is Bar oil?
Hi deecar210...
Bar Oil is a special oil used on chainsaw chains and the bar they rotate around to lubricate them during the cutting process.
It can be bought at HomeDepot, Lowes,Ace Hardware,etc.
Please take time to rate me
9/12/2011 6:41:53 PM •
Remington...
•
Answered
on Sep 12, 2011
What kind of oil do
Hi natcarc2003...
You will use "Bar and Chain Oil",it is used to lube the chain and bar of your chainsaw as you are using it.
You will push down on the top of the oil fill lid to push the oil onto the bar and chain.
It can be bought at any small engine repair shop, WalMart,KMart,HomeDepot,Lowes,etc.
You will fill the reservoir with the oil till it is about 1/2 inch below the surface of the opening of the oil fill on top of the chainsaw.
Please take time to rate me thumbs up
9/10/2011 6:48:39 PM •
Remington...
•
Answered
on Sep 10, 2011
How do I adjust the
Loosen fastener that holds bar tight, turn tension screw clockwise until chain touches bottom of bar lightly.
9/5/2011 11:49:13 AM •
Remington...
•
Answered
on Sep 05, 2011
Electric 12" 1.5hp, need to
Remove fasteners from plate holding bar in place, bar and chain can be removed at this point. To tighten find tension screw, turn clockwise.
9/4/2011 1:04:47 PM •
Remington...
•
Answered
on Sep 04, 2011
Dull chain on chiansaw
Simple. Get it sharpened. Where? A chain saw repair place. Find one in the Yellow Pages.
8/19/2011 2:27:09 AM •
Remington...
•
Answered
on Aug 19, 2011
Can't find manual. What
Chain oil. You can find it at Walmart or anywhere. But you can also just use any motor oil 10W30 or 30W etc.
8/13/2011 1:37:35 PM •
Remington...
•
Answered
on Aug 13, 2011
Saw will not run
Could be a bad power cord, bad switch or bad brushes/springs in the motor. An AC voltmeter is helpful for tracking down these types of problems. Good luck!
7/29/2011 3:19:33 PM •
Remington...
•
Answered
on Jul 29, 2011
14/1/2 in. electric chain saw
Hi, if its electric all you need is bar n chain oil. Any brand is fine. Fill the reservoir each time it runs low ( probably about every half hour of cutting). Hope this helps, regards Phil.
7/19/2011 7:44:22 AM •
Remington...
•
Answered
on Jul 19, 2011
Where is the closest remington
Hi bdshantz,
Welcome to fixya!
Remington chainsaws are made by MTD. The nearest service center for MTD is:
SCHLICHTER'S LTD.
132 QUEEN STREET SOUTH
KITCHENER,ONTARIO
N2G 1V9
(519) 745-5689
Thanks. Please place a vote and keep me working here. :>)
Handie Andie
7/8/2011 7:05:02 PM •
Remington...
•
Answered
on Jul 08, 2011
How do you replace the
Your are going to have to take off the side cover (the bar side cover) and then pull the bar off the two screws a little bit to give the chain some slack. Remove the chain from the clutch drum, replace the chain, and put the side cover back on. Hope this helps.
6/27/2011 9:04:22 PM •
Remington...
•
Answered
on Jun 27, 2011
Not finding what you are looking for?