Crosley CCW5294W Top Load Washer - Answered Questions & Fixed issues

If your washer just keeps filling it and the pressure valve is not to blame I would suggest that your tube coming off of the pressure valve might be blocked or partially blocked. If you have hard water where you live try taking off that line (it just pulls off fairly easy) and squirt some CLR into the tube. A good way to check to see if there is any restriction is when you take off that tube. You should be able to blow though it very easily.

does it fill with machine unplugged? if so change water valve

on models with a cap yes its pressurized and the softener goes down into the line not meant to overflow out of top?

First, you'll need to make sure you have the proper voltage at the outlet, and the power cord terminals fit tightly into the outlet slots. Based on your post, you most likely have a faulty electronic control board.Here is the board to order.

seethis causes and fix it. God bless youUser Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first. Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this time Line Fuse If the washer won't start the line fuse might have blown. Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information. Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced. Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first. Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design. Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design. Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the hom Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.

If your capacitor is shorted that could very well be it.

Service manual

Let me check service matters and see if their is a probo with these vertical modular washers:

Their is nothing about throwing the breaker, they make mention of broken lid switches and a bad counter weight which has been replaced by another component. Might be worth ******* about to your local appliance provider. If the cap turns out to be fine look for objects between tubs or a jammed water pump maybe. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

there may be a problem with the pressure switch.there may also be a problem witht the lid switch.try and unplug the unit and see what happens.
the main control board would be the last thing to go out and need replaceing

check the lid switch

Take off the back panel then inspect to see where the leak come from. Sometimes it leaks at the hose connected to the water pump by a loose clamp, or a deteriorated hose end, then it can be an easy fix. If the leak is from the bottom center tube then the Nut seal at the bottom tube needs to be replaced. This is a hard job so the cost can be high while the part is not expensive. Good luck.

ok try this look under the washer between the motor and the transmission is a motor coupler it may have broken to get to it you need to remoe the motor and the pump very easy job but look between the motor and the trany and you will be able to see the coupler it should be two plastic coggs with a rubber coupler this is usually the problem

there is a fault in the pressure switch, all machine have a pressure switch, this is normally a part about 5 to 8 cms in diameter and about 3 to 5 cms thick with a small pipe running down to the bottom of the drum or some part quite low on the machine that holds water. maybe a drain pipe the pressure switch is located near the top of the machine inside the cabinet somewhere you should be easily able to get to with the lid or back off THIS THIN PIPE could be BLOCKED or has been damaged, it works by the weight of the water pushing air up this pipe to activate the switch, if the machine has been laid down or tipped up it can sometimes be reset by draining every bit of water from the machine, first by pumping the normal way, then unplug from mains and remove a pipe from the pump and drain the last bit out, this sometimes lets the pipe reset itself best of luck, if i have helped please rate me

Question edited for clarity. 'field cycle' to fill cycle. Do you hear water running? Water inlet valve failed. or Taking too long to fill. Check the strainers in the rear where the hose connects and check water flow from the hose. Also try a power disconnect overnight to do a power reset of the control board. ============================================= If the cold water supply is slow or not entering the tub at all, the washer will stop ahead of the rinse cycle while waiting for the tub to fill. This can be caused by a clogged water inlet valve, the main water supply valve being partially closed, or low water supply pressure from the home.

Crosley Washer stops mid cycle - Repair Clinic

https://www.google.com/search?q=Crosley+Professional+Washer+washer+stopping+at+beginning+of+fill+cycle ..

They all have alpha-numerical model numbers, 'Professional is just a 'description' like 'Ford Truck'. See if you recognize it here? https://www.google.com/search?q=Manual+for+crosley+professional+washer ..

No Model # given... Found this https://www.partselect.com/Models/YTW4514PN0DG/ But before throwing parts at it call their 866# for tech assistance.

There could be several reasons why your Crosley washing machine is not spinning properly during a regular cycle. Here are some possible causes:

1. Unbalanced load: If the load of laundry is not evenly distributed in the drum, it can cause the machine to become unbalanced and not spin properly. Try rearranging the clothes and see if that helps.
2. Drive belt: The drive belt may be worn, loose or broken, preventing the machine from spinning. Check the belt and replace if necessary.
3. Motor coupling: The motor coupling connects the motor to the transmission. If it is broken or worn out, the machine may not spin. Inspect the coupling and replace it if necessary.
4. Lid switch: The lid switch prevents the machine from spinning if the lid is open. If the switch is faulty, the machine may not spin. Test the switch for continuity and replace it if necessary.
5. Motor: If the motor is faulty or burned out, the machine may not spin. Test the motor for continuity and replace it if necessary.

If you are unsure of how to check or replace any of these parts, it is recommended to consult a qualified technician.

There are several reasons why your Crosley top load washer might not be passing the wash cycle. Some common causes include:

1. Power issues: Check to see if the washer is properly plugged in and the outlet has power.
2. Water supply problems: Make sure the water supply valves are turned on and the hoses are not kinked or clogged.
3. Load balance: The washer may not be able to advance to the next cycle if the load is unbalanced. Try redistributing the clothes evenly in the drum.
4. Control panel issues: The control panel or the control board may be faulty and need to be replaced.
5. Lid switch: If the lid switch is not functioning properly, the washer may not be able to advance to the next cycle.
6. Clogged pump or drain: If the pump or drain is clogged, the water may not be able to be pumped out of the washer, causing it to stop mid-cycle.

If you are unable to resolve the issue on your own, it may be best to consult a professional for further assistance.

i think theres a problem with the motor control board because of no proper operation or turning it off suddenly. Just try to shut down your breaker and if theres a reset button on your machine press it might help.

possible bad timer or control board

Replace the power plug fuse. Read the manual http://laundry.manualsonline.com/manuals/mfg/crosley_corp/crosley_corp_washer_product_list.html

possible stuck timer or showing the cycle hasnt finished