20 Most Recent Kenmore Whirlpool Duet Sport Washer Door Seal Rubber W10111435 - Page 4 Questions & Answers

On average, washing machines use 19 gallons of water per load, and the average household runs between 5 and 6 loads per week. Based on those figures, most washers use up to 5,605 gallons of water annually. Front-load washers use an average of 12.5 gallons of water per load, while top-load washers average 19.6 gallons per load. Older top-load models manufactured decades ago use 40 or more gallons of water per load. Possibly reading the meter incorrectly... ck here... https://plumbingsniper.com/how-to-read-a-water-meter/ My 1.5" water line to fill my pool puts out 12 gallons a minute it would take 45 minutes running full out to put out 530 gallons. Best to you.

Possibly this.... https://www.appliancepartspros.com/lg-pcb-assembly-main-ebr75639504-ap5681030.html But give them a call at their tech #877 before ordering.

Could be several things. Check this link and give them a call at their 800 tech # to confirm what it might be before throwing parts at it. https://www.repairclinic.com/ProductDetail/939978?symptoms=66

Question edited for clarity. 2 Duplicate questions deleted. Refresh page to see your question.

How to Find the Age of a Kenmore Washer

Hunker https://www.hunker.com > ... > Washer & Dryers Locate the serial number on a Kenmore washer made by Whirlpool. The second letter of the serial number identifies the year the machine was manufactured. For ... More here, but you need Model Number and Serial Number https://www.google.com/search?q=kenmore+washing+machine+serial+number+lookup ..

Is the lid actually locking when lock light comes on? If not, replace lid lock

Washing machines will not spin until they have emptied most of the water from the drum. I would check the outlet pipe is clear and the pump runs with no obstruction first.

https://www.youtube.com/watch?v=I0ECIx4KujQ https://www.youtube.com/watch?v=b977m2jXcog

Hello. I'm a little confused at the description of the problem. You indicated it, "will not agitate during wash cycle or spin during the spin cycle." But later in your description you indicated, "It will however, drain and spin after wash cycle and during the rinse cycle." I'm not sure if you description was an error but it sounds like you will need to replace the coupling which is part number 285753A.

Press, High temp wash, heated dry, High temp wash, heated dry, High temp wash, Heated dry The panel should all light up at which point you need to press cancel. This will reset the control board if it can be reset. If you do not have a "heated dry" button use "saver dry" or "air dry"

http://www.managemylife.com/images/6975/original/346.jpg?1303498921 According to this it could be either the Computer (don't think so but don't rule it out just yet.), the fill valve, or the heater. Appliance Repair Forums This link will help you test the fill valves. This will link you to a service manual for the HE3T washer which is very similar to yours and the diagnostics and tests will be the same. https://www.ifixit.com/Document/1074/.pdf If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

Greetings, Please ensure that the clothes are distributed evenly before using another mode to wash your clothes. It might be that there is an issue with only one of your washing modes. If other modes do not show the issue, then I would turn your washer dial counterclockwise by 180 degrees before attempting the first mode again. Thank you.

Beth it's probably the door spike. You can find additional info at tthese sites. You'll need the Model #. They all have helpful 800#s to talk with a tech and make sure you are getting the right part if there's a doubt or want to talk about your issue. https://www.appliancepartspros.com/ https://www.repairclinic.com/ https://www.partselect.com/Appliance-Parts.htm?msclkid=a7b3213444cd1e09294a4576b9211200 Best to you!

The 27 series are typically 4.5 cu ft. https://manualzz.com/doc/2128222/kenmore-3.2-cu.-ft.-king-size-capacity-top-load-washer ..

One of your parts was faulty on delivery. Due to the cost of control boards, I would always advice a service call so that you get the correct diagnosis and warranty on the part and the labour if it goes wrong. Unscrupulous dealers will sell parts from scrapped machines that haven't been tested. eBay is the worst culprit. ..

Yes it is the Door Switch, or its wiring and where is terminates on the control board. Of the board is faulty. https://www.google.com/search?q=Kenmore+HE2+front+load+Washer.+It+has+F22+error+code ..

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

Question edited for clarity. I presume you want a WIRING diagram? Not much available for that model. Sometimes you will find the service information in a bag taped behind the bottom kickplate or inside the back of the case. https://www.google.com/search?q=Kenmore+HE2+110.46502700+wiring+diagram ..

The E2F2 error code on a Kenmore Elite washing machine typically indicates a problem with the communication between the control board and the motor control board. This could be caused by a faulty control board, a loose or damaged wire connection, or a problem with the motor control board. Here are some steps you can take to troubleshoot the issue:

1. Unplug the washing machine for a few minutes and then plug it back in to reset the control board.
2. Check the wire connections between the control board and the motor control board. Make sure they are secure and free from damage.
3. If the wire connections are okay, you may need to replace one or both of the control boards. You can find replacement parts online or through a local appliance repair shop.
4. If you are not comfortable working with electrical components, it's best to contact a professional appliance repair technician to diagnose and fix the problem.

I hope this helps!

Question edited for clarity. https://www.google.com/search?q=Kenmore+417.44052400+diagnostic+mode

There is a problem with the washing machines drive belt or with the agitator.