Top 20 SanDisk Sansa Fuze MP3 Player Questions & Answers

You may download the manual at http://mp3support.sandisk.com/sansa/UserManual/FUZE/fuze_userguide_en.pdf

The JPEG's that won't display are probably too high a resolution or the file size of the image may be too high. If you are using sandisk Sansa for instance you can use the Sansa Media Converter to change (lower) the resolution of the images, or you can use other software to alter the images.

Hold the on/off slider for 30-40 seconds and then release to reset the device. Then try turning it on. Also, sometimes if the battery is low/dead it will take longer than 3 hours to charge up. If it does not turn on after the reset you might try letting it charge for a day or so and try again. If it doesn't work after all of this, it should be returned to where ever you bought it for a replacement.

Hold the on/off slider in the on position for 30-40 seconds, release, then try to turn on normally.

here is the manual: http://mp3support.sandisk.com/sansa/UserManual/FUZE/fuze_userguide_en.pdf

to my laptop. I am using windows 7. I went to my device Manager, click portable devices folder, under Walkman NWZ-B163F, click properties, update software, it reads : this device is not working properly because Windows cannot load the drivers required for this device. (Code 31).When I click Driver, update Driver, it says (The Best river software for your driver is already installed. Windows has dertermine the driver software for your device is up todate.

Not sure what you mean here as this device has a USB cable and a microSDHC expansion slot. By inserting a microSD or microSDHC card the MP3 player lets you expand its memory up to 32GB. You can obtain these cards from a computer store or online.

I experienced the same problem (my USB device ). try these steps: 1. Start, Control Panel, 2. Performance and Maintenance, 3. Administrative Tools, 4. Computer Management, 5. Disk Management, 6. Find the USB drive (usually the last storage device before the optical drive), 7. Click on the USB drive, 8. Right click on it and you will see the options (New Partition or Format) 9. Follow the instruction (I chose FAT32), but please do NOT chose Quick Format.

To change the language on a Fuze, press the MENU button, select Settings (four vertical slider), select the last item on the menu, then select the sixth item on the submenu.

slide "hold" button, lock the player.Now hold record and power button together. it will say to enter MSD mode. conncet to the computer. it will be displayed in 16mb format. open it, add a folder "sansa.fmt". disconnect from the computer. your sansa is formatted now. u will lose your data saved in it and may not be able to view pics n videos again. bt the sansa will be formatted.

Slide the power switch up, past the "ON" position, to lock/unlock the unit.

no power on no display

Push the power switch up as far as it will go and see if the blue ring on the front of the player lights up.

The Fuze's power button is not a traditional button but a slider, so if you did not push the slider up all the way, this may be the only reason it was not powering on.

Reset the Fuze by pushing up on the power switch and holding it in the up position for 10 seconds.

Try to power on the Fuze again after it has fully rebooted.

Connect the Fuze's USB cord from the Fuze to a USB port on your computer.

You should see a yellow charging light illuminate and the battery symbol blinking on the Fuze's main display.

Once the battery stops flashing, the Fuze is fully charged and you can try to power it on again.

hope this helps

Have you tried visiting the site like it says?

look for the small hole that allows for factory reset.

MP3 players charge up by the USB cable that is connected to a computer or by a 5 volt USB mains adapter.

Hi,Welcome to fixya.Can you please provide the make and model of your mp3 player so that we can guide you on how to delete music.Thanks

Use the power switch. Slide it up all the way and hold it there for fifteen seconds to reset the Fuze.

it is broke

Press the MENU button. Select Reglages (four vertical sliders). Select Parametres systeme (6th item). Select Langue (6th item).