Top 20 Rowenta Commercial Garment Steamer - White Questions & Answers

Check this site out Terry,if not their let me know. Rowenta IS8100U1 A6 Steam Brush Parts

Just pop it off. Need force, no need to take hub caps off.

Unless it smells bad I wouldn't. Just always use distilled water. The unit is boiling the water so what comes out is already disinfected.

Clogged unit, it's over heating. Run vinegar through it to remove deposits.

http://laundry.manualsonline.com/manuals/mfg/rowenta/rowenta_iron_product_list.html

WHen cold tilt over sink and empty and rince every 3-5 uses depending on how much you use it. Water sitting in the tank gets moldy and bad, rinse tank and use Britta type filtered water only.

Anaheim, Berkley, Fresno, Bakersfield, Los Angeles, Long Beach, Sacramento, San Diego, San Jose and San Francisco. Google Rowenta repair Center, choose a city and go!

You have a build up of water In the hose. Sometimes happens because the hose is too low to the ground. Try stretching the hose up and tap it and the water should travel back down the hose. Another reason could be that you are using too much steam for that particular fabric.

The steam not only removes wrinkles, it freshens the fabrics - making them look cleaner. You can use this steamer on clothing, bedding and table linens and also to remove.

50/50 vinegar/water.

see this causes and fix it. God bless you

If the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber .

If the iron produces too much or too little heat, test the electrical cord . Also test and, if needed, adjust calibration of the thermostat .

If the iron does not spray properly, inspect and clean the nozzle.

If the iron leaks or spits, clean the steam vents, nozzle, and tank.

If the iron sticks to fabric, clean or repair the soleplate. If the iron stains fabric, clean the soleplate, clean the tank with a commercial cleaner, and use distilled or filtered water.

go to www. repairclinic.com and get itGod bless you

Look at the manual again maybe theres a button that you have to turn on. Or call the nearest repair man maybe he knows or can tell you.

the power light stays on but steam only comes out for 30 second.and it takes few minutes to steam again.

Well this was helpful but also HELLfull! I guess because I have a 9050 !! I took out the screws & could not remove the hose it was attached with 2 clamps & a washer! I put the whole darn thing in my tub ( I have a sprayer in there) and yes tons of sand, black stuff and cloudy water came out. I had to do this 8 times with the hose attached! Awkward & a mess but it did finally come out clear. BTW I did it through the hose & the bottom hole. On the last run through, after my whole bathroom is soaked including me, the hose popped out! I was cracking up! turns out on the 9050 you simply push down on the ribbed hose covering and it releases. This IS NOT in the manual either. But I'm happy my steamer's like new again & live & learn ;o)

go to www.fitness.manualsonline.com God bless you

1) the thermostat is faulty, clean and adjust.2)If a routine cleaning of steam vents, channels or holes does not clear the blockages, you can use a steam iron cleaner. This is a mild acid type of cleaning mixture specially prepared for such a job. No other form of fluid should be tried; it may damage seals or jointing compounds used inside the iron.God bless you

Rowenta IS8250 Garment Steamer instructions are no longer available from Rowenta.

what brand? what does it look like? should be a heavy screw-on cap on water tank. Fill with soft or distilled water, power on, and should be a red light that comes on when hot enough for steam

Hi, Try puting a cup of white vinegar in and let it sit over night. It should disolve the build up of calcuim. Also try CLR it also will work. Good luck.