Top 20
Maytag Dishwasher Questions & Answers
When we turn on the dishwasher there is no water
hi Mapletonmob.
this is all i could find out.
A dishwasher that will not fill with water can be frustrating and repairing it through a serviceman can be expensive. Even for someone who may not consider themselves handy, repairing a dishwasher is not a difficult process. Below we've provided you with a list of the most common parts that fix a dishwasher will not fill with water. Use this information to help troubleshoot which part is broken
The water inlet valve is used to fill the dishwasher with the proper amount of hot water and is controlled by the timer or electronic control. The valve will be located behind the lower access panel and will have two wires attached to it, an outlet hose to the tub and a hot water inlet from the household supply. If your dishwasher does not fill then you should first check the inlet supply to verify that you have enough water pressure and that you have power going to the valve during the fill portion of the cycle. If these conditions are met then the valve is defective and should be replaced. If you do not have power to the valve then you should look at the float switch, the timer or electronic control or the door switches as a possible problem. All of the electrical checks can be made with a multi-meter.
A malfunctioning float could cause the dishwasher to not fill with water. The float is located at the bottom of the dishwasher tub and acts as a safety device that prevents the dishwasher from over filling with water. The float rises with the water level in the dishwasher and when the proper level is reached, the float will trigger the float switch to turn off the water inlet valve. Check that there is no debris or foreign objects that might restrict the vertical movement of the float and that it engages the float switch located beneath the tub.
The float switch sits below the float, beneath the dishwasher tub. When the float switch is triggered by the float, power to the water inlet valve is interrupted and it stops the flow of water into the dishwasher. Verify that the mechanical action of the float to the switch is operating properly and that the wire connections are secure. To check that the float switch is working properly, remove the wires and test for continuity with a multi-meter.
The door switch is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open. If the door switch or switches are malfunctioning the dishwasher will not fill with water. This door switch mechanism is typically located behind the door panel at the top of the door. To verify the operation of the switches you will need to separate the inner door from the outer door and then remove the wires from the switches and check for continuity with a multi-meter.
We've identified the most common parts that can cause the dishwasher to not fill with water, but there are other parts that could be at fault. If you are unable to fix your dishwasher with the information above,
if none of the above work you might have to call someone out to have a look at it.
11/29/2017 8:42:03 PM •
Maytag...
•
143 views • 0 helpful votes
What is the year of my matag dishwasher DWU7450AAX
Maytag encodes the year and month in the serial number. The 9th position should be a letter that indicates the year, and the 10th position should be a letter that indicates the month. R=2010, T=2011, V=2012, X=2013, B=2014.
4/1/2015 1:39:42 PM •
Maytag...
•
293 views • 0 helpful votes
My maytag dishwasher is leaving a white cloudy film on my dishes that won't come off!
First check your rinse aid make sure you have some in there. I have been told that too much or too little of this can cause problems with etching glass and damaging dinnerware. . I would put a cup in right side up and wash a wash as usual and take the cup out and check that water after. Make sure your using a proper soap, and hot water is getting to your dishwasher. Or has it been full and not really coming out over a long period of time?
Another possibility is it is dirty inside the dishwasher, and not draining?
7/10/2014 11:43:06 PM •
Maytag...
•
533 views • 0 helpful votes
How do I reset the control panel on my dishwasher?
could be wites in the door at the hinge, the microswitches in the door lick assembly, or if it is a series of flashes it could mean a code depending on your model number. Last to check is visuals on the control board for burning, or any loose wiring.
6/18/2014 6:35:55 PM •
Maytag...
•
891 views • 0 helpful votes
Power is to the dishwasher put it wont turn on
hello first check yor breaker make sure not tripped.
next check for lights in your panel.
perform a normal wash if no luck
next perform a service diagnostics cycle.
note sercice diags. works on Maytag MDB7600 series.
press the following keys in less than 6 secs.
HeatedDry > Normal > HeatedDry > Normal
to advance machine cycles press Start/Resume key.
blessings,
e.
5/22/2014 3:11:23 AM •
Maytag...
•
204 views • 0 helpful votes
When is on 5 minits working then display showing end what is the reason
Sounds like a drain problem maybe. Also these tend to have a blinking pattern, sometimes. Or if it is just saying clean, it could mean an error of some other function not working. My guess, the drain is clogged. check to see if you can actually cancel the cycles, fill wash and then cancel it out, then check to see if it drained all the way out.
6/12/2014 12:48:15 PM •
Maytag...
•
49 views • 0 helpful votes
Door seems to lost firm motion it like a sprinf broke?
take off bottom front kick panel and u will see the door springs one on each side. check and make sure they are connected to the cable that opens and closes the door. Look at the springs closely as they could be weak.replace if need be. u can go on line to applianceparts.com to find new springs
4/11/2014 1:33:44 AM •
Maytag...
•
76 views • 1 helpful votes
Thermostat tripping
I just fixed my Maytag's bi-metal switch. I smacked it with the plastic end of a screwdriver. Problem solved. You may have venting issues in the dishwasher if it's continually overheating.
1/30/2014 6:31:32 PM •
Maytag...
•
268 views • 0 helpful votes
MAYTAG DISHWASHER DOES NOT STOP PUMPING
there is a float towards the front of the d.w. usually in the corner.
if its stuck in the up position this would not allow the pump to shut off
4/3/2014 2:03:18 AM •
Maytag...
•
51 views • 0 helpful votes
Clean light blink, dishwasher not working
Does it blink 7 times pause then repeat if so then have a heating problem control does not detect a temperature rise, don't know your technical expertise I ohm out heater at the control easier than pulling out the machine just look for continuity means heater is good if none you'll have to reach under unit to make sure you do not have a burned wire to heater if heater is good ohm out thermistor at room temp should be between 50-70 thousand ohms very seldom does this part go bad but i had one so check it last if both parts check good then the electronic control is not outputting 120VAC to the heater.
2/8/2014 2:59:18 PM •
Maytag...
•
64 views • 0 helpful votes
Water coming in dishes not getting cleaned
Look inside the spin blade and see if there is food or paper inside of the spin blade exit holes blocking it from spraying and spinning. Also if the spin blade is not aligned with nozzle which sprays water into the blade it will not work. I have had both happen several times. Sometimes dishes or pans pushing against the spray nozzle will also miss align the spray jet so the water does not get into the spin blade. I have also had the spin blade be completely worn and would not spin creating the same problem you've had so I had to replace it. Hope this helps.
10/4/2013 1:45:01 PM •
Maytag...
•
120 views • 0 helpful votes
Will not drain complete
if you hear the pump running to drain it there could be some obstructions in the bottem of the dishwasher . the pump is on a timed circuit like other functions if the time is up and the drain is blocked it will leave some water in bottem. just cleaned mine and you wont believe what you can find down there. i reminded my wife its not a garbage disposal too. ha ha .
9/2/2013 3:53:37 PM •
Maytag...
•
69 views • 0 helpful votes
Service manual
Take the bottom kick panel off, there is a plastic envelope attached to it and the notes are in there.
6/8/2013 1:55:40 AM •
Maytag...
•
83 views • 0 helpful votes
Maytag dishwasher error code 96?
Try killing power to the unit, typically this is at the breaker box but from time to time it may be connected to another circuit in the kitchen that may have GFCI circuit. Make sure the GFCI is not tripped killing power.
1/21/2013 9:05:35 PM •
Maytag...
•
179 views • 0 helpful votes
Not finding what you are looking for?