20 Most Recent Jenn-Air 35 in. JEC9536 Electric Cooktop - Page 8 Questions & Answers

Hi

The issue is either the elements itself gone bad and should be replaced or there is a loose/broken wire causing this issue. If both of them are fine then check this diagram....part no 5 is the ballast that is bad and should be replaced. Hope this helps...please post back for further assistance.

Daniel

F1 indicates a clock or touch pad problem. F8 indicates a clock, or ERC (Electronic Range Control) problem. Are you receiving both codes? If so it seems likely that your touch pad and ERC are contained together in one module, and must be replaced. If you find however that they are separate modules it is possible to determine which is faulty by simply disconnecting power to the unit, disconnecting the touch pad from the ERC, and then powering it back up. Wait for a half hour or so to see if the unit sets the error code again with the touch pad disconnected. If it does the ERC is faulty, otherwise it is the touch pad.

Please note that if you do not have experience mucking about in your appliances inner workings it is best that this be done by an experienced technician.

Hi,
Here is a tip that I wrote to give details about why your cooktop will notspark to light the burners..

Cooktop Range Stove spark ignition does not work

heatman101

Hi,

The problem is with electronic control panel board.The part you replaced.Please don't do anything on the board call the technician and ask him to check it.The problem may have occurred due to short circuit on the board.Ask him for warranty replacement since its a new control board you have replaced or some small minor connection problem too.

Thank you for using fixya have a nice day:-)

To do this you will need an expert to help you re-route the power supply of the fan and maybe the inclusion of a new switch as the old one has what it controls. Although it could be done so the switch still controls it if you dont want a new switch. First you have to isolate the fan power source this power source then you connect the cables to the switch where you want to control the fan from,
Hope this solution has been helpful?

Hey t_a_adams - I have the same problem - did you find a solution?

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...Gas Range Repair Burners Keep on Clicking

heatman101

A continuously running electronic spark igniter could be caused by a bad flame sensor (usually a capillary tube) or igniter controller.

If you can disconnect the power to the cook-top then do so..this will give you a little peace of mind...it seems like the switch for that burner is defective(eg: stuck in on position)..the switch is an integral part of the control that turns on the gas for the burner..you may need to replace the control assembly..these are available from appliance parts stores and on-line

Sorry to read about your problem, I hope this helps you out.

get some oven cleaner spray......

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

Sorry to read about your problem, I hope this helps you out.

you can purchase a grill cover, or put tin foil over it..

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

The ignitor module may have gone bad...this is a fairly common problem...Another thing you can do is to look at the ignitors where they come through..make sure that none of them is grounding out...this would cause no spark also....if you have the proper equipment, you can test the input voltage to the ignitor module to see if it has juice...if it does , then most likely the ignitor module...these are available from most appliance parts stores...or the manufacturer

Your front burner is fine. Assuming you have an electric cooktop the problem is in the switch that controls that burner. The infinite control switch. Replace it.

Hi dmoody... You will have to replace the ignitors. To get the ignitors and the button to raise the fan go to http://www.searspartsdirect.com/partsdirect/index.action and enter the model number of your Jenn-Air. You will see excellent diagrams with each part labeled and numbered.
You can then buy the parts you need there or call your local Jenn-Air dealer to compare prices.

Joe

Thanks for choosing Fixya!