Jenn-Air 34 in. Expressions CVGX2423 Gas Cooktop - Answered Questions & Fixed issues

see pics

I'm assuming you mean the railcocks they are usually held on with clamps and screws.

It is beside the thermocoupler , Buy new one .Remove old one . Install new one .

It sounds like you need a new spark module which controls all of the burners. It is part number W10475147. It costs around $115.00!

Yes, it is the spark module. It needs to be replaced. Sometimes it's easy to reach and sometimes not. I am trying to get my hands on a Jenn AirJGD130ADB Repair Manual becasue I have the same problem.

To remove the top so that you can replace the electrodes, you just need to pull all the burner grates off and knobs. Then remove all the burner caps and rings off so that all you're left with is the cooktop and the burner bases. There are screws going into each burner base. Remove all the screws and the burner bases will pull up and off and then you can pull the top of the cooktop up and off.

i have the same issue, did you ever resolve this?

Hello,

One of the switches that turn on the spark when the burner is turned on has became stuck so even when the burner is turned off it still thinks its turned on. It very well could be the one for teh right front burner or any of the other 3 switches.
Depending on your mechanical ability its not too hard to figure out which one it is. What ya need to do is remove the panel over the burner valves so ya can get to the switches which slip over the stem of the burner valves and remove them in the off position and use a meter set to measure continuity and check each of the 4 switches when in the off position and see which one has a circuit (continuity) when off..when you figure which one has continuity when off that will be the one that is causing the stove to spark when off. Be sure to check all 4 since more than 1 could be bad.

BEFORE ATTEMPTING TO DO THAT AND CHECK WHICH SWITCH IS BAD BE SURE TO DISCONNECT THE POWER TO THE STOVE


GENE

The most posible cause is that the ingiter have been mositure probably from a water leak and have be short the wires of the ingiter. Their is a small chance that it will dry by it self and be normal again. If not you can remove the top and reach for the ingiter, is a plastic box with a lot of wires in and out and with hair dryer you can try to dry it. If it still sparking again then you need to replace the igniter

Sorry to read about your problem, I hope this helps you out.

yes needs special tool

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101

ghhdf

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking
http://www.fixya.com/support/r4033033-gas_range_repair_burners_keep_clicking

heatman101

Hi,
Here is a tip that I wrote to help people troubleshoot problems with their cooktops not igniting.

Cooktop Range Stove spark ignition does not work
http://www.fixya.com/support/r5649407-cooktop_range_stove_spark_ignition_not

heatman101

Hi,
Here is a tip that I wrote that will help you with that...

http://www.fixya.com/support/r4033033-gas_range_repair_burners_keep_clicking

heatman101

Either a grounding problem in the ignitor circuit or ignitor leads have been swapped between burners.

01/26/09 My wife decided to give our Jenn-Air a good cleaning. With lot's of soapy warm water she pulled the knobs off and washed under each of them not realizing excess water was now running down the inside of each control knob shaft. The igniter immediately began clicking away as it was being shorted by the conductance of the water now inside of the switch. I had to remove the cover (2-screws) to access the control switches but that is all I needed to do do in order to have clear access. Using her hair dryer it took about 5 minutes of warm air blowing down each of the shafts until the water evaporated and the clicking stopped. Wahla. The old Jenn-Air is back to working order again.

www.servicematters.com/maytag_library/docs/16010492.pdf service and troubleshooting manual above.

Hello. Chances are that something on the stove boiled over or got poured into that burner. take it off, soak it overnight in water with dishsoap added, then rinse it and let it dry before reinstalling it. Repeat the soaking in soapy water if necessary until the flaring, sputtering and black soot is gone. regards, Joe

I have the same model with the same problem. The replacement is simple. Remove the burner cap (no tools needed) Take a large crescent wrench and remove the large center nut holding the burner assembly in place. The ignitor will slide out of the assembly once it is removed. Good luck