20 Most Recent EliteGroup P4M800PRO-M Motherboard - Page 3 Questions & Answers

If you're just looking for the network driver, try downloading the LAN driver off this site.

If it's not installing check to make sure it's being seen by the computer. Click on your start menu and right click on "Computer" (Vista/7) / "My Computer" (XP) and click "Manage". From here click on "Device Manager" and see if the network adapter is listed at all, or if there's anything with a question mark beside it. If there is then try and find out what the device is by right clicking on it and selecting "Properties", under the details tab you can select "Hardware Ids" and find a 4 digit code that comes after VEN_ and before the &. Go HERE and type in the vendor ID, click on the company that the vendor ID matches and search for the device. You can find it by matching the 4 digit code after the DEV_ under the same Hardware Ids list. Just use this to confirm that the device you're trying to install is actually the right one. If it isn't then download the correct driver, if it is then it seems you might have a damaged network card or something is wrong with the OS and is not allowing you to install.

If there's no sign at all of the adapter then there's a good chance the controller is broke and you'll have to look into either replacing the motherboard, or possibly finding an external adapter

You are probably starting to have hardware failure. Since the DMA controller is in the chipset, the mother board will have to be replaced.

make sure the memory is good and the auxilury cord on the motherboard is in. if still no video message me cuz i have board like it.

Unsure you have plugged them in to the right sockets it is an easy mistake to make. If you have them in the right sockets and this has just happened shut your pc down check the connectors are in properly, take them out then back in and reboot. post back if still the same.

I think you should post a detailed information of your problem. 
What the problems you are getting?
Have you Install VGA graphic driver? or
Have you not getting display?
Where you getting this message?
Your operating system boots or not?
Post all ans and problems then only it will be possible for me to solve your problem. Thank you.

Hey

You can get your manual at this site below. Chose the USA to view the manual.

http://www.ecs.com.tw/ECSWebSite/Products/ProductsDetail.aspx?detailid=580&CategoryID=1&DetailName=Manual&MenuID=1&LanID=0

Good luck!

This are things that need to consider in a computer speed performance:
1. Amount of ram memory(If you have only small amount of memory then your computer performance is poor.)
2. Speed of your processor(You should need at least a 1Ghz processor speed or more).

I suggest you increase your ram memory so that your computer will perform faster.

Updating your graphics does not increase your performance.
Versions are not fixed they changed from time to time.
If you want to download then you should download the driver of this chipset "S3 UniChrome Pro 2D/3D Graphics" this chipset is installed in your board
or u can check go to RUN type Dxdiag then press enter Click Yes
go to Display tab u will see your model chipset.
It will work. Good Luck

see the image u get some idea how to connect

You can refer to the motherboard user guide to do the connections.It contains useful pictures and instructions on how to install your motherboard properly.

is it in warranty..?? if not..
do it if u r a professional..

check the following:
1) the cmos battery (above +3v)..replace with a standby n see..
2) remove/clean dust neatly..dust is non-uniform in nature n may cause jam/short circuitry/excess resistace n many more..resulting an increase in heat..
3) open the CPU Heat-Sink with fan out of the socket..put some "Heat Sink Compound" (available in local electronics chip level spare market) between the cpu/processor and the CPU Heat Sink *** fan..resit/fit it tightly in position..
4) may b the smps itself may b defective/faulty or can't produce sufficient wattage supply..check the outputs of smps viz. 0v (black~ground); +12v (yellow); +5v (red, green~ps-on, violet~pg & grey~sb); -12v (blue); -5v(white); +3.3v(orange)..
the 'oscillator and error amplifier ic', or pwm switching regulator circuit..look for defective protector-transformer/resistance(esp 4.7k)/mosfet..
5) ur main/mother board..see with a debug card for mb error..

..plz give higher priority to step3 & 4 (as listed above) CAREFULLY..

immediately contact ur system admin/vendor....

Hello!

In your case, you have problem with some parts of your sound card.Try touch with hand some parts of sound card, maybe have some bad contacts, or bad line (+ or in some case - with motherboard).
Also can be bad chip from sound card.

do it only if u r a professional..

it seems probably the system bios hs been flashed or updated in a wrong way..if so, u gotta replace the m/b, itz a permanent failure..though there r some exceptionals..

can replace the faulty bios if identical (supported,make,model n version) is available..

well to b on safe hand..do the following:..
unplug mains supply..pick open/remove the cmos battery..check (above +3v)..resit..
see if the ram(s) is loose/faulty..open clean/remove carbon & or oxide formed on the teeth with an eraser n resit it..
check for ac main supply and fuse..next check all the outputs of smps viz. 0v (black~ground); +12v (yellow); +5v (red, green~ps-on, violet~pg & grey~sb); -12v (blue); -5v(white); +3.3v(orange)..if faulty try repairing or replacing the power supply with a standby n see..
check the cpu fan rotating and the cpu generating heat..try replacing the cpu with a standby (if no heat is generated)..
there may b a chance for m/b's crystal clock generator to b faulty..try repairing or replacing the m/b with a standby..
there may b also problem with ur monitor or display adapter, try replacing with a standby..

seek professional assistance of ur system admin/vendor....

Here is a link for the manual of your motherboard. All diagrams and specs. should be in there.

Hope this helps.

http://www.ecs.com.tw/ECSWebSite/Products/ProductsDetail.aspx?detailid=673&CategoryID=1&DetailName=Manual&MenuID=44&LanID=0

Hello there
if the power supply fan comes on and the other fans comes on and their is not beeps please try this first unplug the computer and open the case locate the power supply cord that hooks into the motherboard and unplug now press the power button on the computer and hold there for 20 seconds and if it has a reset button press this too now plug in the power cord to the motherboard and plug in the power to the computer and restart and see if this helps ok. if not please let me know ok
best regards michael

hello u must have the processor for your motherboard to work I mean the one that has been working .

with that smell of burning means the processor ur trying to ugrape was not suited for the board so pray that the motherboard is ok

have fune

bye

did you tried to installing the drivers

P4M800pro LAN CARD are no longer available driver for Windows Vista, all you have to do is to buy a new LAN CARD Vista ready.
Actually this motherboard are only have its own lan driver available for 98/2K/XP/2003 but for VISTA i think not.
Hope this might help you some ideas to provide some assistance. Good luck!

HI, all that you have stated in your post points to a damaged Video card at this point. the chip set is damaged and, the card has been rendered useless. If your video processing board is integrated, you will need to disable this section in the driver manager section.

After you have disabled the damaged integrated video processor, you will then need to purchase a stand alone video card to take the place of the integrated card that is damaged. use one of the PCI buses or AGP slot as well. Make sure the power supply ratings match up to the card.

Now, if your Video situation is stand alone, just replace the damaged card with a new card. this will fix this issue.

You may clean the memory board and video card connector with pencil easier and with alcohol the connectors and reinstall it. this will work. or you need to replace the power supply the orange wire 3.3v might be missing or red+5v, white-5v or the purple wire +5v