Kenmore HE2t 3.7 cu. ft. Front Load Washer - Answered Questions & Fixed issues
Lights flashing during cycle
This should take 30 minutes: Remove the panel that is located below the front door, there are 3 small screws located at the bottom that hold this... you will see the water pump, which has a access screw plug. Unscrew this, its like a filter, you may see stuff, like coins, socks, etc, remove and clean out, then put everything back... this should fix the issue.Before you re-fit the filter check to see that the blades of the pump further inside are turning well - no blocks. If the prob still persists you must examine pump.http://www.youtube.com/watch?NR=1&v=4IBvHbQ_3pA&feature=endscreenIf helped click helped.
Leaking hose part no. 1344559
if is leaking by the hose repair or chage and adjust very well the clip or replace because loose the pression.God bless you
Wash Cycle will not start; add garment and door locked lights on.
IF you take the panel off the is below the door, there is a drain plug and you should take it out. YOU will get lots of WATER. Be ready. Clean this out and try again. The issue is most likely the water solenoid valve is bad or the board that controls it is bad. You can also find the tech sheet when you look for the drain. It has all the tests that you can run.
5/17/2019 11:44:46 AM •
Kenmore HE2...
•
Answered
on May 17, 2019
•
6,393 views
Error code f-28
F28 means your washer is locked and not unlocking. To unlock your washer take off the bottom access panel by removing the 3 bottom screws. Reach up near the latching assembly & attached to the door latch is a little plastic pull lever. Pull down on this lever and open the door. Unplug your washer for 60 seconds and plug your washer back in. If the error re-occurs you need to replace your door lock.Click if helped.
5/1/2013 6:07:33 PM •
Kenmore HE2...
•
Answered
on May 01, 2013
•
318 views
Washer wont start
It is
possible that the machine does not start off the cycle because there are errors
due to feedback from the inputs. For the program to start up the main program
controller must initiate the INLET/MOTOR/DRAIN
pump/ valve to open up and allow each function to be driven starting from
the flow of water into the drum as also the drain valve to open to exit the
water at the point of the program cycle. If this does not happen then the
voltage at the valve/motor/pump must be checked or the fault relates to no
voltage from the controller. This means
the controller is a suspect.
If the
water flows though the inlet then the flow pressure should be good, if not the
inlet valve is bad or there is dirt in the filter. Also check the flow at the
inlet of the water line. Once the water comes into the system the WATER LEVEL
SENSOR - normally a pressure switch- must activate at the preset/chosen level
to give the signal to the program controller to switch on the motor. What is
most important for the motor to start functioning is that the door switch must
be ON when the door is shut or this will be an error for starting the motor for
rinse and wash.
Check this
link to replace the inlet valve:
http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html
1/12/2013 11:58:57 AM •
Kenmore HE2...
•
Answered
on Jan 12, 2013
•
45 views
No power or lights, locked
This will be a controller failure, It could be caused by many different faults and would require a service person to diagnose onsite.
3/11/2012 6:06:13 PM •
Kenmore HE2...
•
Answered
on Mar 11, 2012
•
34 views
Not finding what you are looking for?