Whirlpool Ultimate Care II LSQ9564J Top Load Washer - Answered Questions & Fixed issues


Pop the top cover off the agitator to access the 4 agitator dogs.
They must be replaced.

Whirlpool... | Answered on Jan 05, 2020 | 1,342 views


Have you cleaned the water filter out and checked the waste hose first? Make sure you only use a quality detergent as cheap pound shop stuff can rot the sensors, and foul up the camshaft.

Whirlpool... | Answered on Feb 04, 2018 | 201 views


indicates a problem in the timer control
that type of controller suffers from burnt points
have a technician check it out and replace it

Whirlpool... | Answered on Dec 14, 2017 | 616 views


It sounds like the coupling between the motor and gearbox has worn out. It should cost around $15 plus shipping and handling.

Whirlpool... | Answered on Nov 01, 2017 | 1,429 views


sounds like the valve again

Whirlpool... | Answered on Oct 26, 2017 | 198 views


If timer doesn't move through entire cycle, timer is bad. Only exception to that is if lid switch is bad.

Whirlpool... | Answered on Sep 09, 2017 | 129 views


Sounds like a lid switch problem

Whirlpool... | Answered on Aug 23, 2017 | 231 views


Hi,
The problem might be motor is short circuited kindly replace the motor to solve your problem

Whirlpool... | Answered on Jul 23, 2016 | 293 views


usually a transmission problem or program is not setting it to final spin which is higher speed

Whirlpool... | Answered on Jan 18, 2016 | 179 views


If it doesn't fill for the rinse, I would say that the cold inlet valve has failed. Check that the cold tap is turned on and check when the machine fills for the wash cycle and see if it is taking hot or cold water. You will probably find that it is filling only with hot water. A local spares store should have the valve you need.

Whirlpool... | Answered on Sep 19, 2015 | 195 views


Does unit have a reset button? If it has manual control for cycle did you try going clockwise to the start position and then restarting?

If she stopped the cycle by opening the door perhaps that switch is still stuck in an open position.

Whirlpool... | Answered on Aug 31, 2015 | 334 views


are u sure its not just the cap to place fabric softner is missing? possibly in the center of agitator

Whirlpool... | Answered on Apr 03, 2015 | 112 views


is it drains out if so the out let washer/solnoid not is not functioning

Whirlpool... | Answered on Mar 04, 2015 | 88 views


prob b safe with 7kg

Whirlpool... | Answered on Feb 28, 2015 | 198 views


sounds like a broken motor coupling( this machines equivelent to a belt. part number 285753a . mounts directly to the motor shaft and connects to the transmission, order a new one it installs between the motor and transmission,assy

Whirlpool... | Answered on Jan 03, 2015 | 1,294 views


Several things could be causing that. First, behind the control panel check to make sure that the plastic tubing that connects to the water level switch is still connected. The water level switch is the one you use to choose what size load you are washing. If it is connected, trace that clear tubing to the other end to see if it is damaged or if it is disconnected at the other end. An easy and fast way to check the tubing is to fill the washer about 1/4 full of water, disconnect the tubing from the switch in the control panel, the blow air through the tube. If you hear air bubbling from inside of the washer, then the tubing is most likely good and also connected at the bottom end. If the tubing is good, then the switch itself may be bad. To test the switch, use another piece of tubing and (ONCE THE POWER IS DISCONNECTED) blow air pressure into the back of the switch, if you dont hear the switch click when pressure is applied, the switch is probably bad. If it does click, then test the switch with a continuity tester or ohm meter while applying pressure through the tubing. On a GOOD switch, there will be no continuity when enough pressure is applied.

Whirlpool... | Answered on Nov 05, 2014 | 314 views


You can date most of your Whirlpool major name appliances using the service at the following link.

Appliance411 Service How old is my appliance Age finder date of...

Whirlpool... | Answered on Nov 01, 2014 | 389 views


The motor is possibly overheating due to dry bearings, causing the thermal overload to open (it re-closes when the motor cools down).
SOLUTION:
Get some oil onto the felt pads around the plain bearings each end of the motor-where the shaft comes out, you'll be able to dribble it in; at the covered end if you can't prise the cover off, make a hole in it with a philips screwdriver and a sharp 'tap' with a hammer.
I like to use silicon oil but car engine oil would be ok.

Whirlpool... | Answered on Jul 26, 2014 | 371 views


Cycle it again and see if that works, try unplugging it also.

Whirlpool... | Answered on Jul 06, 2014 | 203 views

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

1,616 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...