Whirlpool Ultimate Care II LSQ9549L Top Load Washer - Page 2 - Answered Questions & Fixed issues
My whirlpool washing machine has chipped around
You used to be able to get a brush on product that was used to fix chips in baths and appliances.. I can't remember what it was called, Check around some appliance shops perhaps they might remember?
1/23/2015 11:11:03 PM •
Whirlpool...
•
Answered
on Jan 23, 2015
•
437 views
Why it won't agitate or spin?
if no sound check door switch, if motor runs but doesnt engage transmission check plastic gear between motor and transmission
1/7/2015 1:54:22 AM •
Whirlpool...
•
Answered
on Jan 07, 2015
•
152 views
Discoloration on clothes
I don't believe it is your machine as much as it is your water needs testing. You might have too hard of water.
Possibly rust, calcium, fluoride, or chlorine. Your PH could be too high or too low and your water could be acidic or more likely alkaline. Alkaline water will definitely create anomalous water staining.
10/20/2014 6:56:48 AM •
Whirlpool...
•
Answered
on Oct 20, 2014
•
233 views
How to repair the doggettes
Pop off the cap on top of the agitator. After you've done that, you'll see a bolt head down inside the agitator. Grab a socket wrench and the appropriate size socket and remove the bolt. Then, lift up on the agitator and it should come out. Then, remove that piece that the head of the bolt you removed was holding down. That's where the doggits live. You should be able to figure it out from there.
10/15/2014 1:27:44 AM •
Whirlpool...
•
Answered
on Oct 15, 2014
•
74 views
Where is the water inlet valve
See that thing where you attach your hot and cold water hoses to? That's your water inlet valve assembly.
10/15/2014 1:14:55 AM •
Whirlpool...
•
Answered
on Oct 15, 2014
•
58 views
Whirlpool cabrio washer
Looks like the motor is having a hard time starting. Try changing the motor capacitor, it jump starts the motor. It is cylindrical in shape aluminum color, sometimes black or may even be plastic white. Also, if it is not a direct drive, inspect the drive belt it could be worn out.
8/27/2014 11:42:46 PM •
Whirlpool...
•
Answered
on Aug 27, 2014
•
66 views
How to remove the top part of the agitator of a roper model ras8445kq0
Often agitator tops do spin somewhat freely, for safety reasons. Most of the work gets done at the bottom, anyway. Unless your clothes are getting tied in knots, I wouldn't worry about it.
But if you want to look, they're usually not that hard to remove. I can't picture yours off the top of my head, but look for a cap/cover/cup on top that can be removed by hand, and there might be a bolt underneath that. There's usually a lot of friction in addition to the bolt holding it in place, so you might use an old towel slipped under the agitator and cinched to give you more leverage/grip.
Good luck.
6/13/2014 5:50:52 PM •
Whirlpool...
•
Answered
on Jun 13, 2014
•
119 views
How to uncouple drain hose from top load washer
If your washer's model number is LSQ9549L, grab a pair of vice grips, go behind the machine, squeeze the clamp which holds the drain hose attached to the water pump exit port, and pull the hose off.
You might want to put a towel on the floor before you pull the drain hose off
6/9/2014 8:56:47 PM •
Whirlpool...
•
Answered
on Jun 09, 2014
•
32 views
Not finding what you are looking for?