Amana ALW480DA Top Load Washer - Answered Questions & Fixed issues
Cloth stuck under agitator in washing machine.
there is a bolt under the fabric softner dispenser (if you have one) if not, its a plastic cap on the top of your agitator which pops off by hand or a butter knife.. then there is a bolt under there that holds the unit down..grap the bottom of your agitator and loosen the bolt and remove it...then lift up carefully on the whole thing..careful not to loose the seal and bolt to put the agitator back in place....good luck..
I have an amana washer...Model # 8318015...The
take the bottom panel out(2 screws) then the upper panel out(its clips)
now the pump need to take off the shaft 3 screws then you can put the new belt in it with tention from the pully roller... try to see if there are video for that in youtube...good luck not so EZ to do :(
Timer knob not working
You will need to replace the timer.
Here is the part you need to order.To replace, remove the back cover of the console, remove the knob, unplug the timer and be sure that you have the unit unplugged from the wall before making any repairs!
The part comes with a 365 day, any part, any reason return policy.
Amana washer belt replacement
Steps for Replacing the Belt
Tools needed:
Nut driver or socket set.
Torex screw driver.
1. Unplug the power cord from the
electric socket and
remove the
front panel.
2. Disconnect the power coupling
from the motor.
3. Disconnect the 2 hoses from the
pump. Be aware that the pump
still contains
between 1 and
2 cups of water,
and it WILL
all come out.
4. Remove the belt from the idler
arm, pushing the
belt UNDER the
idler arm. Yes, your hands will
now be quite
greasy.
5. Remove the belt from the main
transmission by
pushing the belt
under the
transmission pulley.
6. Remove the 4 bolts that hold the
motor assembly to
the washing
machine body. Remove the motor
assembly with belt
from the
washing
machine.
7. Turn the motor upside-down. With
the torex
screwdriver, remove the
3 bolts that hold
the pump to the
motor. Remove the pump from the
motor (in my case,
the motor shaft
fit into a slot in
the pump; while
it was snug, it was
not melted or
rusted, and did
just come out).
8. Clean pump and motor as desired.
9. Install new belt and reverse the
steps to
re-install.
Spin cycle does not appear to complete it's
Hi,
Problems with a washing machine not spinning or not draining are often interrelated..
If you are having a problem with your top load washer then check out thistip...
Washing Machine does not Pump or Spin
If you are having problems with your front load washing machine then checkoutthis tip...
Front Load Washing machine not draining and or not spinning
heatman101
No Spin. The water pumps
CHECK IF THE MOTOR IS RUNNING.
CHECK THE FAN BELT.
CHECK THE CONTROLLER.
LASTLY IT CAN BE THE WIRING ALSO.
REGARDS.
DON'T FORGET TO RATE ME
Water leaking into tub from
The water valve is acting as if it has something stuck in the valve holding it open just a bit.You need to take it off and take it apart carefully and clean it out.The water valve is the part where the hot and cold hoses hook to the washer.Hope you found this helpful and thank you for using Fix ya.
My Amana Super Capacity Plus
Hi from retired Englishman in SW France,
The first thing to do is to have the leak investigated by somebody there as we could only offer a list of guesses ;-0)
Once it is empty and carefully lifted onto its side, it should be possible to inspect the hoses and clips and hopefully identify the culprit. In some cases it might even be possible to affect at least a temporary fix whilst obtaining the necessary spare.
Sorry we could be only of limited help in this instance- it's very difficult diagnosing this sort of problem remotely ;-0(
Good luck,
John C
Washer will not agitate or spin
If the unit hums and sounds like it's running but doesn't spin or agitate you've probably got a bad coupler. Open the unit and take the pump and motor off and see if the coupler is broken or missing (This is most often a plastic/rubber part which usually breaks down into three pieces and hooks your transmission to your motor). If it is missing or damaged, replace it. Good luck.
Washer over flowing
you either have a bad valve, bad air switch, or a hole in the air tube leadinf to the switch. An easy way to check the valve is turn the washer on and while its filling unplug it. If the water stops immediately you valve is probobly ok. if it takes a few seconds to stop or doesnt stop at all your valve is bad
Not finding what you are looking for?