20 Most Recent
JVC HD-61Z456 Television - Page 3 Questions & Answers
Power light and red led light blinking rapidly and
This could be easy or hard first i would check the lamp inside this unit and if it looks cloudy,burnt,or has a bulged in the middle peice of the lamp which looks like a stem then i would suggest replacing that lamp, and if that is the issue go to the main menu after the lamp was replaced and working and look for reset lamp timer hit enter .Now if that is not the issue then you could have a problem with the audio IC which is more likely or the power supply.
When the hdmi cable is plugged in the screen
TRY A NEW HDMI CABLE, SOME NEW TV'S REQUIRE 3.1 HDMI CABLE MAKE SURE IT IS THE RIGHT VERSION, THE SOURCE COULD ALSO BE THE PROBLEM, WHAT IS THE CABLE PLUGGED INTO, ECT... CABLE BOX, DVD PLAYER ANS SO ON, SWITCH CABLES AND SOURCES TO ELIMINATE ALL POSSIBLE PROBLEMS
No red when hooking up component cable for dlp hd
Check the red cable this is where the red comes from, you may have a bad cable, maybe use the blue or green one just to see if the red will come through, it can be the cable box or the tv or the cable itself.
I have a HD-61Z456 the
Did you replaced lamp in TV recently?
If not, time to replace Lamp, procedure is written in user manual page-78 and if you need user manual copy, click
JVC Support.
JVC Lamp TS-CL110U is available in
Discount Merchant and after installation of new lamp, turn On TV, go to Menu and reset lamp timer, check page-57 please.
Thanks.
JVC HD-61Z456 Television to dark
Most likely a bad Polarizer within the light engine of which you cannot buy. The entire light engine would have to be re-built or replaced and they usually start around $600.00....
JVC 43" (109cm) HD Ready Plasma TV PD43N30A. Chunghop universal remote codes for JVC pd43n30a
Question edited for a lot more clarity, plus
Chunghop not chungCHOP :>D
JVC: 089, 161, 909
CHUNGHOP Universal Remote Control Codes
codesforuniversalremotes.com
https://codesforuniversalremotes.com > chunghop-univer...
Jul 25, 2019 -
CHUNGHOP Universal Remote Control Codes ; Aiwa: 009, 057, 058 ; Samsung: 618, 619, 620, 621 ; Philips: 013, 023, 024 ; Hisense: 676, 677, 707, 898
My JVC TV has an onscreen remote that doesn't let us use the actual remote what do I do to gat it out?
Hello! If your JVC TV is displaying an onscreen remote and you're unable to use the actual remote, you can try the following steps to resolve the issue:
- Power cycle the TV: Turn off the TV and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on. This can often reset any temporary issues and restore the functionality of the actual remote.
- Replace the remote batteries: Check the batteries in your remote control and make sure they have enough power. If the batteries are low, replace them with fresh ones and try using the remote again.
- Check the remote control sensor: Ensure that there are no obstructions between the remote control and the TV's remote control sensor. Clean the remote control sensor on the TV with a soft, lint-free cloth to remove any dust or debris that may be interfering with the signal reception.
- Reset the TV to factory settings: If the issue persists, you can try resetting the TV to its factory settings. Keep in mind that this will erase any personalized settings and restore the TV to its original configuration. Refer to the user manual or the manufacturer's website for instructions on how to perform a factory reset on your specific JVC TV model.
- Contact JVC customer support: If none of the above steps resolve the issue, it's recommended to reach out to JVC customer support for further assistance. They will have access to more specific troubleshooting steps and can guide you through the process of resolving the issue with the onscreen remote.
Keep in mind that the exact steps and options may vary depending on your specific JVC TV model. Refer to the user manual or contact JVC customer support for model-specific guidance.
Not finding what you are looking for?