20 Most Recent GE Profile WPRE6100G Top Load Washer - Page 2 Questions & Answers

hi
the solution is so simple, you have to open it
and clean the plastic pipe that runs from the tub to the load switch, sometimes gets dirty with detergentes and mud.

Must be the tub seal is still leaking, you may not have got it seated real good and you need to let it dry for 24 hours before using

aCTUALLY IT MAY BE THE LID SWITCH BUT iM THINKING ITS THE CAM DOGS OR IN G.E MODELS THE AGITATOR COUPLER AT THE BOTTOM IS BAD? ITS ABOUT 7 BUCKS TO REPLACE IT AND EASY

Are you asking about installing the inlet water valve?? Remove the screws in the back top edge of the control panel and tilt the control panel forward. You can now see the valve. There will be either 2 or 3 electric plugs on the valve that just pull off. Then 2 screws holding valve to machine. remove screws and lift valve. 1 spring hose clamp will be left holding valve to machine. Slide clamp away from valve--pull off small hose and the valve is out. Reverse procedure to reassemble.

Judy, You can go to the following link to find out how old your machine is. A good rule of thumb is 10% for each year of age that you would deduct from new price. Appliance411 Service How old is my appliance Age finder date of...

Few digits missing at end of model # And you have not told us what the washer problem is Light on motor will tell a code by series of blinking lite . Many of these type of washers we found in servicing them electronic brake stops working. one of the common parts that go bad not a cheap repair. Next is the motor itself Stater&motor speed board all one peace. another high dollar part. interface board at top. and don't for get the lid switch. and a few other problems these washers have. that we have seen . Let us know what problem your having. Glad to help R.A.P. Ken

pour warm water and thoroughly clean it after sometime

The most common solution for this message is to turn the machine OFF and then ON. If the error resets, you are done. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control. Solution:

1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.
2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.
3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Bad connection on led board may need new board

check ur hoses and ur water pump

need to change control board, on top ,opens from the back.

A blown fuse is a serious electrical hazard. It means that you have a short to the ground terminal of the washer's plug. I recommend you disconnect (pull the plug) until the short is sorted out. I don't know if you have been into the washer and made a short or not, otherwise you have some defective electrical part. Depending on the age of the washer and cost of repair technician and replacement part whatever it is, it may be prudent to find a lightly used washer that is working properly.

hi, laying a spirit level across the top of the washing machine while adjusting the front feet....you will need help to do this... In Rare cases the fitting to the drum can come loose... Hope this helps... Regards

The first thing that comes to mind is that the drain hose might be too low and is siphoning the water out of the wash machine as it is filling. Try to raise the drain hose up and see if that helps any. Let me know how it goes.

Over loaded? otherwise bad drive belt on bottom, or unlikely, bad motor.