Frigidaire Affinity ATF7000E Front Load Washer - Answered Questions & Fixed issues
Frigidaire Affinity washer won't fill
My affinity atf8000fs1 won't fill with water. I replaced the inlet valve, pressure valve, Main board and power board and door switch. Same result. It starts, locks door, I hear clicks as if it is cycling to next phase, but water does not fill the tub. This is a front load model. Anything missed before I part it out?
11/27/2021 7:28:59 PM •
Frigidaire...
•
Answered
on Nov 27, 2021
•
1,091 views
Frigidaire Affinity showing EF2
Ef2 could mean the vent hose is blocked or has come off.Slide it out from the wall and make sure the hose is ok.Hope this helps.
4/6/2020 8:19:45 PM •
Frigidaire...
•
Answered
on Apr 06, 2020
•
2,547 views
Washer won't start and the door is closed tight
Replace the door lock, takes about 10 mins. Just replaced mine. Ordered it from Amazon for less than 40.00. You take the top off and unscrew the lock from the front. Reach in and pull up, unplug old one, plug in new one. put new one back in the holes, screw it in tight. Put the top back on and your done. Don't forget to unplug it before you start.
11/24/2019 9:14:11 PM •
Frigidaire...
•
Answered
on Nov 24, 2019
•
814 views
Hi, I recently purchased a 6 year old condo and
The result of cool water temperatures and milder detergents, is a buildup of oil and grease in the machine, which produces oily smells in the laundry. Grease and oil can take many forms, ranging from automotive lubricants to greasy foods to oily toiletry items, and, over a period of time, these oils can accumulate and become trapped in various parts of the machine, particularly in the door seal of front-loading machines.
Run an empty cycle with HOT water and a detergent that contains bleach to remove grease and oil from the appliance. However, be sure to use bleach designed specifically for laundry, as opposed to using regular bleach. ie OxyClean. and or a cup of vinegar.
Best to you.
2/26/2018 4:50:33 PM •
Frigidaire...
•
Answered
on Feb 26, 2018
•
468 views
Dryer wont heat up
Good Afternoon Friend,
I understand that you are having trouble with your Frigidaire Affinity dryer not heating up. There are some things that you are able to try. First check to make sure that the lint filter, the ducting, and the outside vent, are clear of lint and not constricted in any way. Second, reset your appliance by either unplugging it or shutting the power off at your homes circuit breaker for 3-5 minutes. Once power has been restored, run any cycle. If you are still noticing that your dryer is not heating, I suggest contacting your local authorized technician for further assistance. They should be able to diagnose your dryer and determine why your appliance is not heating. Hope this is helpful.
-Best Regards-
WP
12/28/2017 4:03:39 PM •
Frigidaire...
•
Answered
on Dec 28, 2017
•
798 views
My Frigidaire Affinity ATF6000FS1 front
It's the timer control, not the motor or filter. Try a different setting. You should also be able to find more information on the manufacturers website, along with a manual and possibly a diagram. Also You Tube is a good place to find out more on how to repair it.
12/3/2017 8:37:19 PM •
Frigidaire...
•
Answered
on Dec 03, 2017
•
523 views
I have a Frigidaire Front Loader Washer Model #
You need to lean it back and remove the lower panel, you will have complete access to the water pump, disconnect hose clamps,remove and clean the rubber boot,disconnect electrical connector and 2 screws holding pump, Replace with new pump, before beginning take pictures to ensure proper installation
11/19/2017 3:25:26 PM •
Frigidaire...
•
Answered
on Nov 19, 2017
•
542 views
Washer quit working in middle of cycle, won't even come on
Look under the washer. Is there a little pile of black rubber shavings? With the heavy load, you may have broken the basket coupler between the motor and the drum. Try turning off the selector, and move it one click at a time towards the end of the cycle and turning back on. Hopefully it will drain for you. If the coupler is the problem it is inexpensive to fix. Some also call this part the "clutch". It kind of looks like a hockey puck with six holes in it... three for the motor, three for the clothes drum.
I attached pictures of a couple types. This part is a common problem when you put a heavy load in, because the rubber takes more stress.
7/10/2017 3:31:58 AM •
Frigidaire...
•
Answered
on Jul 10, 2017
•
133 views
My front loader flashes E52 call for service
Hello willkie6 - An error code E52 typically relates to the speed control board or the motor itself. An experienced service technician would test these parts by measuring the resistance of the motor to distinguish exactly which part it is. This is not a typical do-it-yourself job. Personally, I would recommend reaching out to a qualified appliance repair person who will be best able to pinpoint the exact problem causing the error code. I hope this information helps to some degree.
6/30/2017 2:25:47 PM •
Frigidaire...
•
Answered
on Jun 30, 2017
•
707 views
Washing Cloth Diapers with Extra Ingredients
You can strip cloth diapers to help bring back absorbency. I use a simple method of washing clean diapers in the hottest temp possible with blue liquid Dawn dish detergent (1 teaspoon for HE washer, 1 tablespoon for older machines). I also add 1/2 cup bleach because it disinfects and sanitizes. Bleach has always been safe for me but im sure there are alternatives if you don't like bleach. Then a few hot rinse cycles and a regular dry cycle and diapers are more absorbent and odor free.
5/5/2017 10:55:44 PM •
Frigidaire...
•
Answered
on May 05, 2017
•
148 views
How to fix error e23 on toshiba washing machine. machine runs for a whikle and then stops
Error Code ( E-23 )--------Clean the LID LOCK sensor,its almost located where you can see the LID LOCK came OUT and IN or Moving--which is functions to LOCK and UNLOCK the door cover ( Symptom ++ the LID LOCK will moving OUT and IN),open all the cover ,take out the LID LOCK sensor,open the LID LOCK sensor case until you can reach the COPPER connector which is act as the SWITCH .CLEAN the COPPER with paper sand or anything possible but not to damage the copper.After all put it back to the place intact.Hope it work,Mine worked with this procedure.+++++Toshiba AW-SD120S COST=== FREE OF Charge ( Do It Yourself )
12/19/2022 6:25:38 AM •
Frigidaire...
•
Answered
on Dec 19, 2022
•
14,301 views
Not finding what you are looking for?