Top 20 Bosch Nexxt 100 Series WFMC1001UC Front Load Washer - Page 2 Questions & Answers

Does the problem occur on both hot and cold washes. If not then check the inlet solenoid . If yes than check the board.

Try this download http://laundry.manualsonline.com/manuals/mfg/bosch/wfmc1001uc.html?idRes=550112

Are there any lights on at the washer? If not check the washer circuit breaker in your house main circuit breaker/service panel. If it is tripped reset it and try start button again. If it trips again you need a service call. If there are lights on try turning the washer main knob to off and unplug the washer from the wall outlet...wait 10 seconds then plug in and try start button again.

Okay if the drum inside is Plastic then YES, You can get a sealant to block off holes ,depending on how big the rip is,I wish you joy and if there is any thing else I can do or Advise then please ask.

Try restarting it, make sure the load isnt to heavy, if that does not help, call a local repair man.

CHELL TRY TO DO A WASH WITH OUT CLOTHES,AND DO A SHORT PROGRAMM.

Check the way the waste pipe is connected to sink drain,could be purge back from here or could be faulty/ leaky fill valve,

try eSpares. Bosch parts are expensive but alternatives are usually available. They also have video tutorials for fixing common problems. Bosch website usualy has diagrams in the spares section. Are you 100% sure it is the control board? It could be something else causing the control board to freeze. For example I recently had to replace the drain pump on our machine.

my machine did that when stuck on spin cycie all i did was unpluged it for a few seconds and pluged it back in and it let me start all over again and open the door

follow this steps and fix it. God bless youDrain Pump Filter This is the most common problem. Some have a small cover in the lower front put a screwdriver in the hole and turn counterclockwise to remove. There will be a cover to remove, water will come out so be prepared with a towel or wet vac. Clean this out. Other Machines will need to access the drain pump to get to the filter. This can be done by remove back panel on some washers. On others you will need to remove the lower panel or complete front panel depending on model. The filter is located inside the large hose from the tub to the pump. remote the hose and filter. Drain Pump The drain pump may have failed. If you hear it making noises you will need to remove the drain pump and check for obstructions, broken impeller, or not spinning freely. Remove obstructions if it does not spin freely replace the drain pump. If you hear it hum replace the pump if nothing is found inside. If no noise is heard check the pump for power. To do this remove the wire connectors and connect a voltmeter turn to a drain cycle, refer to tech sheet or service manual for proper voltage reading, usually any voltage would probally indicate a faulty pump. If no voltage to the pump replace the main control board. Hoses Check the hoses from the pump by disconnecting them and make sure there are no obstructions. Check your hoes drain, if it is a slow drain this can cause your washer to not properly drain.

Make sure dial is switched to 'off'. Unplug your machine, then plug it back in. Hold down the rinse and delay buttons with one hand. With the other hand, switch the dial from off to cold or warm or whatever cycle you want. All the buttons flash a few times, then just the start button flashes. If if doesn't work, do it again.

To get the clothes out if you are having trouble, open door manually. Near the bottom of this cover is a small hole. Insert a piece of wire into this hole, and push in gently. While pushing, turn the cover clockwise, it will came off. The door release is a narrow white plastic strip hanging down on the right; Pull down on this strip while pushing in on the door, the door lock will release.

Click helped if helped.

Maybe you just need to change the motor brushes. YouTube has some great videos. Spares here on Fixya. Did you check out your filter?Click if helped.

Sounds like you don't have any water entering the machine, check that you have not inadvertently switched the isolation tap off. (Just because the tap looks in the right position, don't be fooled, if it the small plastic lever type, these can splay and appear to be on when the fitment under it is in the off position and vice versa, good luck.

For parts look in Fixya. For changing go to YouTube, great videos to show you how.Click helped, if helped.

Turn program selector to "off". Turn selector to Drain or Spin. Press the start / pause. Wait until program ends. Open door.OR Press "start / pause" until the start / pause light flashes.

OR

First, unplug the machine and turn off the water supply. On the lower right of the front panel is a 6" / 15mm cover. Near the bottom of this cover is a small hole. Insert a piece of wire into this hole, and push in gently. While pushing, turn the cover clockwise, it will came off. The door release is a narrow white plastic strip hanging down on the right; Pull down on this strip while pushing in on the door, the door lock will release.

Pl click if helped

Suggestion plug off the wall for 30 minutes, may re-set.

Check motor brushes. Power should be disconnected.

Maybe you just need to change the motor brushes. YouTube has some great videos. Spares here on Fixya. Did you check out your filter?Click if helped.

Check the pump filter. This is located at the bottom front right of washer. Look for a drop down flap or cover, once located, unscrew filter anti-clockwise to remove and clean. Be prepared for a lot of water and junk. If you find a closed hose pipe when you remove the drop down flap it is to drain excess water.The pump itself is directly behind the filter housing, check if there is nothing stuck in the housing, especially after you are cleaning out your filter after a long time. Clean out and refit carefullyPl click if helped.

Are you running a load according to the care labels?? If you run delicate or easy care items on a cotton wash this can happen. Just because an item is 100% Cotton doesn't necessarily mean it will tolerate a cotton cycle check the care label. Also, if for example a cotton cycle is 6Kg, the easy care will be 3-4Kg, Delicate and woollens will be approx 2Kg. Overloading can cause items to knot during cycle. Finally, check that your inlet water is not too hot. Repost if you need any further assistance