20 Most Recent
LG WM2487H Front Load Washer - Page 7 Questions & Answers
Water is leaking out from
Sounds like you have a blockage here, try pouring kettle of water in and make sure goes away/remove clean soap dispenser if not and check for any obstruction in soap to drum hose.....
Cant get washer door open
unplug washer for few minutes then plug in as soon as you hear a click pull on door between clicks call for service
My lg WM2487H*MA leaks small
Hi
Remove the dispenser, pour water into the opening and make sure water can get into the machine freely. Inspect the opening for soap build up. If water goes down slowly then open the washer door and check at the bottom for anything blocking the water inlet port into the washer (socks can sometimes cause a blockage).If it all checks out ok, make sure the machine is properly leveled and not leaning forward.
Also check the link bellow for more details:-
http://lgknowledgebase.com/kb/index.php?View=entry&EntryID=6283
Please get back to us if you have further query else please accept the suggestion.
Thank you for contacting fixya.com
I recently moved to another
the tub has stabilizers on it ... remove rear panel and make sure the shocks are still attached and or not broke... if all this looks good is the unit on a pedestal if so there have been alot of problems with lg washers and pedestals.... i know your saying well they sell them with the washer as a optional feature ,but they have been giving fits to lg for the last couple of years.... if the shocks look good then most likely you have a bad hall sensor located also in the rear of machine on the part called the stator .the stator is a round device that attaches to the rear of tub and has a copper coil that goes around the entire thing... on this device is a white plasetic device called a hall sensor that measures the spped and balance of unit if unit starts getting out of balance the hall sensor will slow machine down.... good luck to you
Soap ispencer jammed
Welcome to fixya
Hello
I have a solution for this
Press Ok, Accept or replay so we may get started
Your pre-solution is coming up shortly
PLEASE
REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL
My name is Bruce
How do i fix the
Problem:
An occasional LE error but always a slow or no spin.
Solution:
A Red wire going to the Hall sensor was intermittent. You can test this from the main board connector down to the connector on the hall sensor by checking continuity. There is an intermediate connector down by the motor/hall sensor so you can isolate the problem even more. Problem was in the short wire harness that connects directly to the motor and hall sensor. Could not find the open point of the wire so added a new red wire and integrated it into the harness.
A service manual and more LG washer notes are HERE If you need further help, reach me via phone at
https://www.6ya.com/expert/dan_73bbd84fe1d95b61
Water wont load why I put the machine on wash
Hello & Welcome to FixYa
The problem seems to be with the water inlet valve that has gone bad and needs replacement. Before replacing the valve try swapping the connections and clean the inlet valve. If the valve is fine then the problem is with the pressure switch that needs replacement. Please get back to me if you have any other questions.
Kevin
Water wont load
Hello & Welcome to FixYa
The problem seems to be with the water inlet valve that has gone bad and needs replacement. Before replacing the valve try swapping the connections and clean the inlet valve. Please get back to me if you have any other questions.
Kevin
Water wont go into machine
Hello & Welcome to FixYa
The problem seems to be with the water inlet valve that has gone bad and needs replacement. Before replacing the valve try swapping the connections and clean the inlet valve. Please get back to me if you have any other questions.
Kevin
No water comming thru. Buzzing soundf
This is the water control valve. It should fill on either hot or cold. One of them will be good. The washer has one for hot water and one for cold.
Code fe
FE Over Flow Error
Water is overflowing (water level frequency is over 213).
If FE is displayed, the drain pump will operate to drain the water automatically.
(may be too much suds ...)
WM2277HW Service Manual
HERE...
Or
Locate your service manual behind the kick panel of the machine.
FE means overflow condition.
Before replacing the fill valve sand or trash may have gotten into the tube going from tub to water level switch.
So find that hose and blow it out. Remove the standing water and retry.
Thanks for using FixYa!
Wm2487hrma washing machine front loader.
That type of movement of the drum is typical of a front loader as it will be either spring or damper suspended. If no noise then as you say, not likely to be bearing but may be worth checking that all springs/dampers are attached or all have the same resistance?
Our LG front load washer and dryer are so out of
there must be a broken spring in the washer or a strut bar has come loose this unit should not be doing this. as per its age alone if you are some what technical remove the lid and check all four springs are attached and all five struts in line if not have it looked at it does not cost as much as a new machine these can be the only faults so you know what your looking for it will be hard for a service maN to rip you off
best of luck
please take the time to rank this advice
and have a merry christmas
LG Front loader humming, not filling with water, or operating
its not the filter problem.the motor is faulty and that needs replacement.
you can get motor at
www.repairclinic.com
to avoid circuit board damage do not try to on the machine again n again till the motor gets replaced as it can short circuit the main board too.
Not finding what you are looking for?