20 Most Recent LG LFX25960ST Stainless Steel French Door Refrigerator - Page 2 Questions & Answers

ice tray heater is not working due to bad icemaker timer. thanks .

check for broken springs. thanks .

Scott probably control board needs relpaced

I have the same problem and I know the solution. For LG to get their "in the door icemaker" to work, they have to blow cold air into the door's icemaker compartment. This air travels through two vents located just inside the refrigerator on the left side. The problem LG has is that the seals between the door and the refrigerator for these vents leak. This means that cold air is vented into the refrigerator compartment. Any sensitive food placed on the bottom two shelf on the left side will freeze. I can place two bowls of water in my refrigerator and make ice in 6 hours, even though the refrigerator is set to 38 degrees. The good thing is that LG knows there is a design problem and they know they can not fix it. After calling LG repairmen out for my freezing problem and not getting the seals fixed, LG gave up. Of course LG will try replacing the seals, and then replacing the door; but the real problem is a bad seal design. Just keep putting bowls in your refrigerator and as long as they continue to freeze up, keep calling LG back and demand that they fix the problem. LG can not fix the problem because it is a bad design, so now I am getting a new refrigerator Model LFX 29927, which is better and has dual icemakers. If you an LG refrigerator with their in the door icemaker, place two bowls of water inside the refrigerator, and if your seals are bad and they freeze; complain to LG until they give you a new refrigerator.

That is the symptoms of failure of the=> EBR34917104 Main Control Board APPLIANCE911 Item location 500A HERE

Three things could be wrong: Solenoid switch where the water comes into the unit has gone, this control the flow of water into both the ice maker and the water dispenser. If the switch is good and then you need to check your filters, sometimes inside the door top right. or on one of the corners on the bottom front.. You should be able to unscrew them with you hands.. make sure water is off behind unit or where ever your shut off is at. One last thing.. check for kinks in the water line behind the unit if it was pulled out lately.

Sounds like the power to the solenoid valves that allow the water to either come out the door or go to the ice maker, is not present.

bnbgdflcdg nd;klh djope'j;e m;jbdb.vkigm; sgups gbdvbxcvx

I would say the light switch is stuck or "welded" contacts. In my ge, the light switch is in the upper part so that the switch moves up into the upper right surface when the upper right part of shelf slides against this switch. The sliding part of the switch may be dirty or perhaps broken off. so the switch stays on all the time. My freezer side has the same switch arrangement. Look at your freezer side to see what the switch looks like and how it is supposed to work. Appliance parts sites usually have parts and instructions for how to replace.

You.have to check if the compresor is working or damage. Try starting direct the compresor, Generali should be the electric part outside the compresor just change at the electric parts and should work. If you send a picture of the position on the connectors I will help you to try the compressor

The drain tube is frozen or clodded

probably filter backwards? or wrong filter? why did u put new filter in? cuz it stopped already, and thought new filter should fix problem? u guys kill me

To reset is to repair, this error message it telling you that your Ice Fan is probably not running which is contained in the freezer behind the extra large bulge on the top left freezer evap cover. The fan has failed due to either normal failure, or it's iced over. Usually they become iced over as a result of other issues in the freezer compartment. A qualified service tech is recommended looking at the unit to see if there is a clogged defrost drain issue, an overall defrosting issue, that the freezer evap cover has not been substituted with a newer designed one, (which there are several updates). You should pull the plug on the unit, leave all doors open for a solid 24 hours to ensure a full defrost of any excess ice or frost in areas you can't see, and start over. The unit will most likely resume functions without the error message if the motor was simply iced over, until it possibly returns. Pleazer Appliance...

To reset is to repair, this error message it telling you that your Ice Fan is probably not running which is contained in the freezer behind the extra large bulge on the top left freezer evap cover. The fan has failed due to either normal failure, or it's iced over. Usually they become iced over as a result of other issues in the freezer compartment. A qualified service tech is recommended looking at the unit to see if there is a clogged defrost drain issue, an overall defrosting issue, that the freezer evap cover has not been substituted with a newer designed one, (which there are several updates). You should pull the plug on the unit, leave all doors open for a solid 24 hours to ensure a full defrost of any excess ice or frost in areas you can't see, and start over. The unit will most likely resume functions without the error message if the motor was simply iced over, until it possibly returns. Pleazer Appliance...

if the dent is not creased; use a suctioncup dent puller availlible at any autoparts store

you need to have someone check the defrost circuit. if the unit does not defrost properly , ice will accumulate on the back panel where the evaporator is, blocking the evaporator fans completely, and the circulation fan will eventually stop working because the ice buildup contacts the blades all the fan motor, and eventually the refrigerator compartment will start to get warmer and warmer because there is no circulation of cool air.

Mybe it's too late for you but this could be helpful for somebody else. The part number is 3391JA2055A - meat tray assembly. It's the one with the "Chef Fresh" tag.