kawasaki 19.2V 4 Piece Cordless Tool Kit - Answered Questions & Fixed issues

Following I think I have the same problem

Where i can purchase 19.2v drill adopter and charger in bangalore

I will sell my charger. My motor went out on my drill. [email protected]

My motor went out on mine. I have two batteries I will sell. [email protected]

I have a trigger out of a new drill. My motor went out. Do you want to purchase the switch? [email protected]

Re: Burned trigger switch: call the number on the drill (800.590.3723) and tell them what happened. They will offer to send you a new switch or have you send the drill in for replacement of the switch--although the person I talked with said they would probably just replace the whole drill.

Try tapping on the sides of the drill to see if that fixes your problem. If not then you might try to get ahold of Kawasaki and see if theres anything they can do under warranty.

Call the service # and they will send you a new drill, mine had a burn mark right through the switch and with the model # they replaced it mine was a21.6 they are having troubles with the triggers i pulled mine a part and when i put a battery in it it would run continuous , the number should be on the drill1-800 590-3723

Danger!!! There is a RECALL NOTICE in effect for batteries and chargers for Kawasaki 19.2v systems. Go to the website and check your model number and they will ship you a free charger, if your model number is affected, RECALL NOTICE

Hi there, let me see if I can help.

1.Since this is a 4 piece kit, test the batteries in some of the other tools to make sure the batteries are good

2. This could be a malfunctioning unit, If you just bought it, take it back to the store and get a replacement, (you may have to take in all 4 and do a complete swap but most home improvement stores have no problem doing this)

3. The Forward and Reverse selector just above the trigger is stuck in the middle meaning, the drill is not in forward or reverse and when you press the trigger nothing happens. See Page 15 of this PDF for more information.

4. If none of this works, there is a Recall for that Battery Unit. Check This PDF to see if what you bought applies.

Hope this helps.

Brian

check voltage on batterys with volt meter if the batterys are weak try recharging. try them in flashlight or other peice of equipment.. try moving forward reverse switch while pressing trigger and maybe clean battery contacts with eraser.

sounds like your connections from battery to charger are dirty not making contact when did you buy it?

when the battery is fuly charged if im not mistaken the green light will still stay on but will not be charging the battery anymore. All the light is doing is indicating that the battery is fully charged. It is not recommended that you leave the battery sitting on the charger for long periods of time since batteries an get a memory from a charger and then you might start having some battery issues. Hope this helps.

your trigger switch is going bad

As long as the drill bits do not have points on them you can drill plastic ect.
The short bits are for working in tight areas.

whas the drill stuck? if so you will need to open it and see if the coal is intact, if not change them and it should work just fine, if not try to clean the motor

You can try Alltradetools.com and under parts/service they will advise you how to go about it. You will need the tool catalog number handy when contacting them. Let me know if this works because this is the first time I have tried them.

You can go to AllTrade tools and search your tool. If your model number is affected there is a recall notice on Kawasaki tools. They will send you a new charger kit, transformer and base.

frist of all .there is no recall by Kawasaki on this unit!!!!!!!!!, if anyone tells you that there wrong. There are two units soled, one is green and black. this unit is for small home uses only, and its not for sheet rocking and or deck building. The other unit made, is a Little tougher. but steel for home use only, that one, is the black unit and sliver. the problem is over use of the unit, and using it, for what it was not designed for. The company that makes this unit is coming out with A higher amp switch. The company is (All trade) please use the unit for what it was designed for. Now to clare fy I'm A kawasaki engine and power service center, along with over 82 Manufacture and hundreds of products. this unit is not warranted by kawasaki bit by ALL Trade. thank you, good luck

check with kawasaki to find the problem. well get back