Top 20
Kodak EASYSHARE 5300 All-In-One InkJet Printer - Page 2 Questions & Answers
Printer not printing
Inkjet printers need to be used frequently to prevent ink drying out and blocking the print head nozzles. If the print head cleaning maintenance routine does not clear the blockages, then print head needs replacing, but it may be expensive. It may be more cost effective to buy a later model and better printer than replace the print head.
Error code colour cartridge not installed corectly
Try removing the cartridge, then re-inserting it. Make sure it clicks into place. If you still get the error, shut down the printer, then turn it back on. If you still get the error after that, unfortunately it may be a bad cartridge.
Print drivers
Hi,You have not mention the New PC Operating System. You can download and then install the drivers from the link ->
Click HereRegards,Sean
Does not print evenly. Some lines are very faint.
Hi,Welcome to FixYa.Since you have already performed calibration and cleaned the printhead, kindly verify that the ink cartridges are not damaged and are completely seated in the printhead:1. Lift the printer access door, then remove the ink cartridges from the printhead.2. Verify that the labels on the ink cartridges are intact, and that the cartridges are not damaged.3. Verify that the KODAK Ink Cartridges have not been refilled.4. Insert the black ink cartridge into the printhead, then press down firmly until you hear it click into position.
5. Insert the color ink cartridge into the printhead, then press down firmly until you hear it click into position.
6. Close the printer access door.7. Check the printer status monitor on your computer (or the LCD screen on the printer) to determine if there is sufficient ink available for your print job. NOTE: When the "Black ink cartridge is low" or "Color ink cartridge is low" message is displayed, print quality can be affected.8.Reprint the original picture or document that had the quality problem.Hope this helps. Thanks for using FixYa.
I have lost my disks fore Kodak easyshare Ai0
Hi, Welcome to FixYa.You can download the installation software from manufacturer's support website by clicking this
linkOn the page which opens, click the "
Download" button to start the download process.Kindly refer the detailed installation instructions given on the download page to install the printer.For your reference, here are the installation instructions again:
Installation Instructions
- Verify that your computer meets the system requirements. NOTE: WINDOWS XP
64-bit Operating System is not supported.
- Disconnect your all-in-one printer from your computer.
- Verify that you logged on to the computer using the administrator
account.
- Close all programs.
- Download the software onto your computer.
- Double-click the *.exe file, then follow the on-screen
instructions.
- When the installation is complete, connect your all-in-one printer to your
computer.
- Select Start > Programs > Kodak > Kodak AiO Home
Center.
Hope this helps. Thanks.
My 5000 aio will not print black, other colors OK
Hi,
The following may work: remove all the ink supplies. Remove the printhead and soak it for about 5 minutes in 0.5" of very hot water. Gently blot the printhead on a soft damp paper towel to remove the excess water, then replace in the printer and then reinstall the ink supplies.
Kodak easyshare 5250
just simply pull out the old cartridges on the printer then check the no. of the cartridges or simply bring it to the computer store where you purchase the said unit
On the Kodak ESP 5200
Hi!
The 3501 error code means "acces door open"
Please be sure that the printer's acces door is well closed.
If this doesn't fix the problem, please do the following:
1. Turn the printer off by pressing the on/off button
2. Unplug the power cord
3. wait for 1 minute
4. plug the power cord back in
5. turn the printer on
Hope it helped.
Regards,
Bogdan
Screen shows fatal error code 3809 please advise
try this steps based on the given instructions from other forums.
To resolve this error:
- Disconnect the power adapter from the printer.
- Wait 30 seconds to allow the printer to reset.
- Connect the power adapter to the printer. Turn on the printer, if necessary.
If the error continues:
- Open the printer access door.
- Remove and install the printhead two times.
- Close the printer access door.
- Wait until the printer is ready to use.
- If problem persist better to send your printer to the technical person near on your place
I need sthe Kodak Easy
Hi,
You can download the printable version of the manual from the link below.
Hope this helps. Good Luck.
~SmokinJoe~
My Kodak printer is only
the cartridges come with tape over the print heads to keep them from leaking during shipping.
Remove the tape and put the cartridges back in.
Installed a new ink cartridge
An ink cartridge may be incorrectly installed. Follow thesesteps to make sure the cartridges are correctly installed:
- Make sure the Epson Stylus NX400 is turned on.
- Do one of the following:
- If your printer indicates that an ink cartridge is expended, press OK.
- If your printer does not indicate that any ink cartridge is expended, press SETUP, select MAINTENANCE, and press OK. Then select CHANGE INK CARTRIDGE and press OK.
- Open the scanner.
- Open the cartridge cover.
- Press down all the ink cartridges until they click into place.
Note: If a cartridge is properly seated already, you may not hear a click.
Caution: If you remove a low or expended ink cartridge, you cannot reinstall and use the cartridge.
- Close the cartridge cover and push it down until it clicks into place.
- Close the scanner.
- Press OK to begin charging the ink. This takes about 2 minutes.
You'll see a message on the LCD screen when ink charging is finished.
Caution: Never turn off the Epson Stylus while ink is charging or you'll waste ink.
If you remove an ink cartridge for later use, protect the ink supply area from dirt and dust and store it in the same environment as the Epson Stylus with the label facing upward. Note that there is a valve in the ink supply port, making covers or plugs unnecessary, but care is needed to prevent the ink from staining items that the cartridge touches. Do not touch the ink cartridge ink supply port or surrounding area, and do not store the cartridge upside down.
Not finding what you are looking for?