20 Most Recent
Sony KDS-R60XBR1 60" Projection HDTV - Page 3 Questions & Answers
Red light blinks 3 times
Yes, there were and are known issues--"lamp door not properly closed" means that but something else.What happens is door is warped from heat from lamp----with door off set will not function due to the safety switch----want to know if switch/door are the real problem?Engage switch with something not metal and try to turn set on--if it and lamp come on do not look at lamp directly----do not operate with level bypassed and door removed as heat can warp the outer plate if no door.If it comes on door is the problem---look at it edgewise---if warped a little the tab on back of door that engages the lever does not do its job.If does not come on with lever engaged something else is wrong.There was a recall that has ended regarding this---some were so bad they melted the lamp housing and even fused the front door of the lamp to the plastic around it.Let me know what you find.
KDS-R60XBR1 AKB circuit fault
AKB is auto kine bias---means a problem related to one of the three picture tubes or the boards connected to each---if it showed in error buffer with a number to the right that is the number of times the error has been detected.
No sound
Try putting in a DVD or VCR tape..if they don't make any sound either...than you have probably blown an audio board fuse... But I bet that they will have sound which in that case the problem is more than likely the cable ITSELF not the box... the cable that carries the signal your tv has video on one wire and audio on another.. then sheilding etc.. it's probably got a short in audio ( I have seen brand new cables to do this so even if it looks ok try different one.) if that don't work... hook a different tv up at that location and see what happens... and then it's to call cable company to come fix the box which probably blew up scrambler... which would show that the output is working fine but unfortunately your tv is not able to dis cipher the audio because it's a tv not a cable decoding device...I hope that helps you.
Sony kds initial setup issues
This could be a issue in the set or from a box if one is used for signal--try unplugging set, a box if used and a receiver if used for a while---plug back and see if a reboot of the units solves this or not.If the box is used try if it has them the audio/video outs from the box to the rear audio/video inputs on set to see if same issue.
Best way to test exhaust fan in tv
The set may have more than one fan but---look on the fan as usually the voltage it uses is indicated--if so and removed apply the same voltage to it with it removed--either it runs or not.There should be a service manual available online free for this set--the schematic will show what voltage is used....that error code is just a general indication of what is wrong--if fan not getting voltage, not getting turned on, or bad.
SONY KDS60A2000 will not turn on,flashes green
Hi,do you hear any strange noises? If you hear clicking or like wanting to turn on it could be the board that powers the lamp it's called the ballast.It's major symptoms are clicking,electrical sounds,shuts off and on and get the lamp indicator.But if you don't hear any strange noises,tv is around 6000 hrs,2-4 yrs,It's major symptoms are clicking,electrical sounds,shuts off and on and get the lamp indicator, it could be time to replace the lamp.The lamp you need is XL5200 you can find it here:http://www.discount-merchant.com/Sony-Grand-Bare-Lamp-XL-5200-p/sony_xl-5200u_replacement_lamp.htm?Click=48173.Have a blessed one!
Red standby blinkig light 4 time on a sony 60 in wega
4 Blink 9 out of 10 times is your lamp fan. Check and make sure it clean and free of debrey. Spin it and see if there is any grinding noise. If after you clean and reassemble and the set still shuts down, either replace the lamp fan or check your outher 3 fans as well.
Model kdsr60xbr1 3 blinks
Should be lamp door is not closed---usually means the door is slightly warped from heat.If you follow the procedure to get at the lamp--remove the door and examine it edgewise---if slightly bowed (does not take much) note the plastic peg on the back of the door.When the door is in place the peg engages a tiny lever in an opening behind it---this is to prevent the set from being operated with door off.What I do to prove or disprove this is with door removed use something not metal to engage the lever (push it back) and see if set will come on.If it comes on DO NOT LOOK DIRECTLY AT THE LIGHT WHICH CAN DAMAGE YOUR VISION.DO NOT OPERATE SET FOR PROLONGED TIME WITH DOOR REMOVED AND SWITCH BYPASSED IN THIS WAY.DO NOT PUT OUTER BEZEL BACK WITH DOOR REMOVED AS HEAT FROM LAMP CAN MELT IT ALSO.This will tell you if the door is your problem or not--several class action lawsuits were settled but that has ended now.Let me know if you have questions or need any help.SD TECH
Picture stopped working
Important thing here is when it flashes red---it should be a specific number of blinks---that is a error code.Confirm model number and if possible the blink code.
How do I fix the ballast in a KDSR60XBR1
For the most part a ballast is not "fixable" it is sold as a part--complete.Tell me what set is doing including what lights on front on or blinking?If you blindly just want to replace it GOOGLE THE MODEL NUMBER WITH BALLAST to locate the part and price for it.???
Not finding what you are looking for?