20 Most Recent
Maytag Neptune MAH7500WH Front Load Washer - Page 3 Questions & Answers
Washer machine wont rinse or open door
did it drain after wash? there is a green pull cord hidden at front of detergent compartment to open door. if it did not drain but pump tried, then clean out hose to pump in rear of unit. remove rubber hose from tub at pump and look for obstructions.
water will come out even if tub empty
Won't spin
Replace the wax motor in the door lock mechanism.
Hotpoint WD860P - F5 error
Remove lower rear cover of washer, locate and remove large black hose to bottom of tub.
Remove and clean plastic filter located in the hose, check pump for blockage, refit filter and hose , and test for leaks.
Plz rate my solution.
Thanks.
Hotpoint WD860P F5 error
F05 - Pressure switch jammed on full.
The pressure switch needs testing and possibly replacing unless this is a drain problem. Most likely something caught in the pump which
is accessed by removing the small panel at the rear/bottom of the
machine. The pump slots in place and can be removed by lifting and
shifting to the left. Unscrew the pump off or remove the pipes will
reveal all.You can sometimes test them by blowing into the
part where the pressure tube goes, but only blow gently. You should
hear it click when you blow into it.
Good luck with the machine.And for further doubts please do post comments.
Leak well after completion of wash cycle - Neptune Front Loader
peace,
ngafm1 at your service,
Water sprayed out of ( the leaky washers in the hot water shut off valve which need to be replaced.
They are inside all valves and wear out in time from normal use!
Or you can have a bad solder joint at the junction between the hot water shut off valve or the the pipe joint!
these washers in any shutoff valve can leak intermittently till they get worse and then leak all the time!
you should be able to stand there and watch it as you open and close the shut off valve again and again , and then stay there and watch it start leaking!
Or when you are opening it and closing the valve 4 times straight you may feel a trickle of water from the valve stem!!!!
This means washers in the valve stem need to be replaced!!!
Get a new plumber !!!!!!!!!!!!!!!!!! I'm no plumber but I do under stand this!
Bless You,
please give me a good rating here at fixya.com before you sign off!
The washer(MAH7500WH)doesn't work
peace,
ngafm1 at your service,
Below is the site to get and download the user manual for your
Model MAH7500WH Washer
Maytag is owned now by whirlpool and that's why the web site says Whirlpool corp.com below!
http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=MAH7500&siteCd=MT_EN_US#owners_manuals
Bless you,
nagfam1.
Please give me the best rating here
at fixya. com before you sign off!
Thank You
Mah7500aww
post your email i will send you the test procdure
Control board
have you the touch onsole first to se if it was ok there have been more problems with tha then the cpu board? do you get any beeps while touching it??
Mah7500aww
what it sounds like is the drain from your house wher the washing machine drain hose hooks into is daraining slow so after it spins and pumps the water out the pump shuts off but the drain hose is syphoning the water back into the machine,theres probally lint built up in your drain pipe
Machine is leaking detergent
check inner gasket for small hole
u can take front off by removing screws from around inside door frame (including hinge screws) the panel will pull out towards u then u might be able to c where its leaking better
Control panel
sounds like bad control board
may cost a couple hundred
Maytag Neptune mah7500aww adding water to wash cycle problem
Your inlet valve at behind top of machine is defective; or the pressure from your faucet is insufficient.
Close your faucet valve on wall & unscrew your hoses to check screens on hoses & machine. Clean out well. See that the water pressure is good. Refit, check for leaks. If this is not the problem change your inlet valve, it is easily done.
Sites for spares:
RepairClinic.com (which is good)
espares.co.uk
AppliancePartsPros.com
Pl rate if helped.............
Door won't open
If you open the detergent dispenser and feel along the front edge behind the removable cup there is a coloured cord usually red or green in colour this in an emergency door release, by pulling on it firmly the door will unlock.
Maytag Neptune hot water wont shut itself off during ENTIRE cycle!
The water inlet valve is probably defective. There's two solenoids on the inlet valve. One controls the cold water, one controls the hot water. This is also known as a "mixing valve" on some washers. There are a few things that can cause this problem:
1. Water pressure on the hot water tap is too low and not closing the solenoid diaphragm all the way (minimum pressure should be between 10-25 psi).
2. The filter screen on the hot water side needs to be cleaned thoroughly.
3. Valve is defective.
If you have tried cleaning the screens, and have never had water pressure problems before, I would bet the valve needs replaced. I could not find an exact match for the model number you provided, but repairclinic.com has Maytag Neptune parts. Double check your model number and use the search feature on the website. There are two water inlet valves listed there. Depending on which one you have, it can cost between $30 and $74. I hope this helps you. Post back if you have any further questions.
Water leak
you ll need to reomve the front cover and see where the wate ris coming from, 2 screws hold the door on, and the 2 screws opposite to door hinge will remoive the fron t panel, you then be able to see where it sleakin, before you drop the front panel run you hand on the inside of the door ( the boot is only made of rubber ansd is possible tht it has a small rip in it allowing water ot leak out during cycle.
Not finding what you are looking for?