20 Most Recent Maytag Neptune MAH5500B Front Load Washer - Page 7 Questions & Answers


when unplugged? indicates its the water inlet valve, check it with meter and it may seem good electronically however it may still be bad manually. even though u get an OHM reading. at times it may fluctuate or not put out enough current.

Maytag Neptune... | Answered on Mar 30, 2015


Not sure bout ur code. but a no spin is either a bad door switch, a bad motor coupler or belt, bad clutch or tranny.

Maytag Neptune... | Answered on Mar 29, 2015


unless you know how to replace the transmission on it I would look for a new one

Maytag Neptune... | Answered on Mar 27, 2015


e spares england

Maytag Neptune... | Answered on Mar 22, 2015


LR code is usually caused my the motor and motor control board. if you have 120v to the motor control board and remove the multi pin connector and see if the motor goes in to a 50rpm spin. But more than likely it is those 2 parts. If the tub is noisy or hard to turn in spin motion it may be a bad rear bearing putting strain on the motor also.

Maytag Neptune... | Answered on Mar 17, 2015


Have you checked the thermal fuses? The main cause of dryers not starting is the thermal fuse.

Maytag Neptune... | Answered on Mar 06, 2015


replace the control board to solve that problem

Maytag Neptune... | Answered on Mar 03, 2015


check door inter lock

Maytag Neptune... | Answered on Mar 03, 2015


Because the cycle hasn"t get to the point yet were the water need to pump in to the washer so you have to leave the washer on to work it self. u might have mistakenly stopped the washer yourself after u turned it on or something else is wrong and u have to give us some more info on what's going on . Now let just try this and see if ur washer will work.
Let restart the whole process again, the normal way u start ur laundry,
1, Turn washer off ( Like you're done washing )
2, Now put a new load into the washer, check all button to make sure they are in the right position then turn washer on.
Still not working. Then we need some more info or you need to call someone to take a look at it .

Maytag Neptune... | Answered on Mar 03, 2015


Is it spinning but not pumping out the water? If so, I would make the suggestion that you have something stuck in the pump. I have worked on many different washers and if it's not the timer, the pump is the issue.

Maytag Neptune... | Answered on Mar 01, 2015


the 06 code refairs to motor problem or mcu control board,i assume the machine is not turning this is because a wire has come apart from the motor, or the mcu board needs replaced as it can no longer read the signal from the motor.adrian,,,,

Maytag Neptune... | Answered on Feb 28, 2015


"DO" means door open. If it smells hot, unplug the washer and have a professional check it out.

Maytag Neptune... | Answered on Feb 28, 2015


need door gasket

Maytag Neptune... | Answered on Feb 27, 2015


d DUH in the water along with the cllothes

Maytag Neptune... | Answered on Feb 25, 2015


  1. Your Maytag Neptune washing machine displays error codes, also called "help codes," to identify specific problems with your washer. Once you close your Maytag Neptune's door, the machine locks the door, goes through the selected wash cycles and unlocks the door when the laundry is finished. Error codes appear when there are problems with the door, the inflow and drainage of water and the motor.
  2. Do
  3. Your Maytag Neptune washer displays the "do" help code when the washing machine is trying to start a cycle, but the door is open or not locked properly. If this message is displayed, close the door securely and restart the washing cycle.
  4. FL
  5. The "FL" code indicates that the washing machine was unable to lock the door after you closed it. Open and close the door tightly, then restart the washing cycle.
  6. Sd
  7. The "Sd" code indicates that you have added too much detergent to the washing machine and your laundry has too many suds. The machine will stop displaying this code if it has successfully run the suds recovery cycle, which removes the excess suds from the wash load. If the code remains, reduce the amount of detergent in the load. Use less detergent for similar loads of laundry in the future.
  8. PF
  9. The "PF" code indicates that a power failure has occurred. Restart the wash cycle. If the code still appears, check that the washing machine is still plugged in to the electrical outlet.
  10. Nd
  11. The "nd" code indicates that your Maytag Neptune is not draining as it should. Check that the drain hose isn't kinked and that the stand pipe isn't clogged. If you find either of these problems, fix them before restarting the washing cycle.
  12. LO
  13. The "LO" code appears when the washing machine has finished the selected wash cycle, but cannot unlock the door. Verify that the door is closed properly, push the "Off" button, and wait two minutes. The door should unlock and the error code will disappear. If the error code remains, unplug the washing machine, wait two minutes and plug it back into the electrical outlet.
  14. Lr
  15. The "Lr" code indicates that the washing machine's motor is not running as it should. Have your Maytag Neptune washing machine serviced by a certified Maytag repair professional.

Maytag Neptune... | Answered on Feb 25, 2015

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

3,972 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

606 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Neptune Maytag

  • Neptune Maytag

Most Popular Question

stinky towels

  • Washing Machines
Loading...